Roland XV-2020 Mode D'emploi page 143

●Data Transmission
This instrument can use exclusive messages to exchange many varieties of internal settings
with other devices.
The model ID of the exclusive messages used by this instrument is 00H 10H.
❍Data Request 1RQ1 (11H)
This message requests the other device to transmit data. The address and size indicate the
type and amount of data that is requested.
When a Data Request message is received, if the device is in a state in which it is able to
transmit data, and if the address and size are appropriate, the requested data is transmitted
as a Data Set 1 (DT1) message. If the conditions are not met, nothing is transmitted.
Status data byte
F0H 41H, dev, 00H, 10H, 11H, aaH, bbH, ccH, F7H
ddH, ssH, ttH, uuH, vvH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev: 10H - 1FH, 7FH)
00H model ID #1 (XV-2020)
10H model ID #2 (XV-2020)
11H command ID (RQ1)
aaH address MSB
bbH address
ccH address
ddH address LSB
ssH size MSB
ttH size
uuH size
vvH size LSB
sum checksum
F7H EOX (End Of Exclusive)
* The size of data that can be transmitted at one time is fixed for each type of data. And
data requests must be made with a fixed starting address and size. Refer to the address
and size given in "Parameter Address Map" (p. 146).
* For the checksum, refer to (p. 159).
❍Data set 1
DT1 (12H)
Status Data byte
F0H 41H, dev, 00H, 10H, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H - 1FH, 7FH)
00H Model ID #1 (XV-2020)
10H Model ID #2 (XV-2020)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of the data to be sent
bbH Address: upper middle byte of the starting address of the data to be
sent
ccH Address: lower middle byte of the starting address of the data to be
sent
ddH Address LSB: lower byte of the starting address of the data to be sent.
eeH Data: the actual data to be sent. Multiple bytes of data are transmitted
in order starting from the address.
: :
ffH Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the address
and size given in "Parameter Address Map" (p. 146).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to (p. 159)
Status
F0H
Byte
F0H
41H
dev
42H
12H
aaH
bbH
status
ccH
ddH
:
eeH
sum
F7H
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the address
and size given in "Parameter Address Map" (p. 146).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to (p. 159)
Status
F7H
MIDI Implementation (en anglais)
Data byte
41H, dev, 42H, 12H, aaH, bbH, ccH,
ddH, ... eeH, sum
Explanation
Exclusive status
ID number (Roland)
Device ID (dev: 10H - 1FH, 7FH)
Model ID (GS)
Command ID (DT1)
Address MSB: upper byte of the starting address of the trans-
mitted data
Address: middle byte of the starting address of the trans-
mitted data
Address LSB: lower byte of the starting address of the trans-
mitted data
Data: the actual data to be transmitted. Multiple bytes
of data are transmitted starting from the address.
:
Data
Checksum
EOX (End Of Exclusive)
Status
F7H
143