Barbecook Cebu 4.1 Instructions D'assemblage page 40

• Once you have checked for leaks,
turn off the gas, rinse the connec-
tions with water and dry to prevent
the formation of rust.
• Turn the cylinder knob to the left to
close the cylinder.
Note: the regulator may be different
from the one illustrated here.
WARNING: You must carry out these
leak tests even if your appliance is set
up by the dealer or the shop.
REPLACING THE CYLINDER
When changing the gas cylinder, ensure
that the knobs on the barbecue are in the
OFF position and that the gas cylinder is
closed. Do not replace the gas cylinder
close to anything that may produce a
flame or spark.
TRANSPORT AND STORAGE OF THE
GAS CYLINDER
Although perfectly safe when handled
correctly, lack of caution may result in fire
and/or explosion.
To minimise the risks:
• Never store the cylinder in a buil-
ding, garage or other enclosed area,
but always in a well-ventilated area
• Never store the cylinder in the
vicinity of another gas operated ap-
pliance, or in a very warm area, such
as a car or boat
• Always keep the cylinder out of
reach for children
• Always transport and store the cylin-
der in an upright position
• Do not smoke near the gas cylinder.
USE
PRIOR TO FIRST USE / AFTER
PROLONGED PERIOD OF NON-USE
Do not use the barbecue before you have
read, understood and checked all informa-
tion in this manual.
Ensure that:
• The barbecue is correctly installed
• There is no leak in the gas supply
(see 'Leakage test')
• The burners are correctly installed,
the venturi tubes are properly placed
over the openings of the gas valves
(Fig. D), and there are no obstruc-
tions (see safety information and
cleaning of the burners)
• None of the gas supply hoses can
come into contact with a hot surface
• Your barbecue is installed in a safe
place
40 www.barbecook.com
All manuals and user guides at all-guides.com
D
LIGHTING THE BURNERS
Prior to lighting the burners, all checks and
procedures detailed in the chapter 'Before
the first use' must have been carried out.
• The lid of the barbecue must always
be open when you light the burner(s)
• Do not bend directly over the barbe-
cue when lighting the burner(s)
• The control knobs of the barbecue
must be 'OFF'. Slowly open the gas
cylinder valve. Before opening the
control knob of one burner, wait ap-
prox. 10 seconds to allow to gas to
stabilize
• Important: first light the middle bur-
ner
• As soon as one burner has been
lighted, you only need to put the
control knob of the other burner(s) in
the position 'HIGH' to light them.
• Never try to light all burners at once
LIGHTING THE BURNERS WITH THE
IGNITER
The battery is not supplied as standard.
• Open the lid of the barbecue
• Open the gas cylinder valve.
• Press the igniter until you hear
sparks
• Holding down the igniter, press the
control knob of the middle burner
and turn to 'HIGH'
• If the burner does not light after 3
attempts, disconnect the gas and
wait 5 minutes before trying again.
This will allow the accumulated gas
to escape. Try again, repeating the
above steps.
• If the burner still does not light, read
the chapter 'Troubleshooting Guide'
to determine the cause and the re-
medy, or use a match as described
below.
LIGHTING THE BURNERS WITH A
MATCH
Left and right at the bottom of the burner
box is a small opening that can be used to
light the burners with a match, if the elec-
tronic igniter does not work. (Fig. G)
• Open the lid of the barbecue
• Place a match in the match holder
provided (Fig. G)
• Hold a burning match through the
hole, approx. 13 mm from the burner
• Open the gas cylinder valve.
• Push the required control knob and
turn to 'HIGH'. The burner should
light within 5 seconds. If not, turn
the control knob off and wait 5
minutes to allow the gas to escape.
• Repeat steps 1 through 5. If the
burner still does not light after 3
attempts, read the chapter 'Trouble-
shooting Guide'
G
LIGHTING THE OTHER BURNERS
• As soon as the first burner has been
lighted, you only need to put the
control knob of the other burner(s) in
the position 'HIGH' to light them.
LIGHTING THE SIDE BURNER USING
THE IGNITER
First open the lid of the side burner.
To light the side burner, use the igniter on
the control panel and the control knob on
the side table.
• Press the igniter until you hear
sparks.
• Holding down the igniter, press the
control knob of the side burner and
turn to 'HIGH'
• Repeat a number of times if the
burner does not light immediately.
• If the burner does not light after
5 seconds, turn the control knob to
'OFF' and wait 5 minutes to allow
the gas to escape.