Publicité
light and the black wire on the licence plate illuminator, twist the stripped ends together and fit
one female bullet connector over the two wires before crimping, as shown in picture 47.
Repeat the process above to connect the yellow wire on the tail light with the red wire on the
licence plate illuminator.
The remaining red wire on the licence plate illuminator also needs a female bullet connector
fitted.
With the bullet connectors already fitted onto the three wires of the OEM loom, connect the
wiring connectors as follows. Connect the brown wire from the loom to the connector with the
black wires. Connect the red/grey wire from the loom to the connector with the yellow & red
wires. Connect the remaining black/grey wire from the loom to the connector with the red
wire. Alternatively, these same connections could be soldered and protected with heat-shrink
supplied.
Re-connect the indicator connectors and use any remaining cable ties and self-adhesive cable
clips (item 3) if necessary to neatly organise the wiring, before reconnecting the rear loom
connector to the main loom underneath the ECU, as shown in picture 51. Ensure that this wire
along with the wiring extension is positioned over the top of the cross brace on the rear sub-
frame, as shown in picture 49.
Re-fit the ECU into place along with the plastic cover on top, locating the two tabs at the rear
and the push rivet at the front, as shown in pictures 3, 4 & 52.
It is advisable at this stage to check for the correct operation of all lights.
With the wires clear of the locking mechanism, re-fit the riders seat, along with the pillion seat
or seat hump, as shown in picture 53 and secure using the original bolt as shown in picture 54.
Ensure the tail tidy is securely mounted and all bolts are fully tightened.
Re-fit the licence plate (it may require drilling).
Depending on local laws, attach enclosed reflector in an appropriate location.
Test the license plate illuminator and all lights before riding.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill
and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring
that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at
its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or
used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing
death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the
amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory
rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in
re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 28/11/14 (AR)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
