Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. LP0111BK
  6. Instructions de montage

R&G LP0111BK Instructions De Montage

Masquer les pouces
1
2
3
4
5
6

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
FITTING INSTRUCTIONS FOR LP0111BK LICENCE PLATE BRACKET
M-V AGUSTA F4 2010- / F4RR CORSA CORTA 2011-
Page | 1
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike
T
(
)
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
FOR CLARITY OF INSTRUCTIONS ONLY
5
3
4
6
2
1
7
9
8
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com
1

Publicité

loading

Manuels Connexes pour R&G LP0111BK

Sommaire des Matières pour R&G LP0111BK

  • Page 1 FITTING INSTRUCTIONS FOR LP0111BK LICENCE PLATE BRACKET M-V AGUSTA F4 2010- / F4RR CORSA CORTA 2011- Page | 1 THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of...

  • Page 2: Tools Required

    LEGEND ITEM 1 = LICENCE PLATE BRACKET (TB0111BK) (x1). ITEM 2 = 150mm LENGTH OF HEAT SHRINK (x3). ITEM 3 = M6x16mm LONG BUTTON HEAD BOLTS (x2). ITEM 4 = M8 PENNY WASHERS (x5). ITEM 5 = M6x20mm LONG BUTTON HEAD BOLT (x1). Page | 2 ITEM 6 =2.5mm x 60mm LONG CABLE TIES (CT060BK) (x3).
  • Page 3  FIT NEW LICENCE PLATE ILLUMINATOR (ITEM 7) TO NEW LICENCE PLATE BRACKET (ITEM 1) AS SHOWN IN PICTURE 3, HEAT SHRINK IS SUPPLIED TO PROTECT THE WIRES (ITEM 2) .  PLEASE NOTE YOU WILL NEED TO GLUE THE LIGHT SHROUD TO THE LED LICENCE PLATE ILLUMINATOR BEFORE FITTING USING SUPER GLUE.
  • Page 4  REFIT LICENCE PLATE (IT MAY REQUIRE DRILLING).  IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON THE LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE HITTING THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD.

  • Page 5: Outils Necessaires

    FRANCE INSTRUCTIONS DE MONTAGE DU SUPPORT DE PLAQUE LP0111BK M-V AGUSTA F4 2010- / F4RR CORSA CORTA 2011- Page | 5 VERIFIER QUE TOUTES LES PIECES PRESENTEES SUR LA PHOTO PRINCIPALE SOIT PRESENTES DANS LE KIT DE MONTAGE. LIRE TOUTE LA NOTICE AVANT DE COMMENCER LE MONTAGE.
  • Page 6  Enlever le cache câbles d’origine présent sur le support de plaque d’origine et retirer les clignotants d’origine et fixer les sur le nouveau support. Utiliser les vis d’origine et les rondelles M8 fournies dans le kit. (voir la photo 3) . ...