Publicité
Liens rapides
DS-PD2-P10PE
10m Digital Pet Immnue PIR Detector
EN50131-2-2:2008
Security Grade (SG) 2
EN50131-1:2006+A1:2009
Environmental Class (EC) II
Diagram references
1
A
D
G
Printed Circuit Board (PCB)
Lens Collet
Casing Screw
B
E
PCB Screw
LED Light Pipe
C
F
Lens
Nut
2
3 3
O
3 4
EOL Resistor Headers: The DS-PD2-P10PE has 2 sets of header pins . These
headers are used to select the End of Line resistance for EOL wiring applic a
NOTE: If EOL wiring is not used, leave the headers OFF.
3 5
Remote LED Enable: This is used when the LED is disabled via the LED ON/OFF
link. To enable this feature the LED terminal needs to be connected to an output
on the control panel. When the system is in walk test mode the output should
be at 0v. For Pyronix panels the output would usually be programmed as
'Remote LED enable'.
3 6
A
N/C - Normally Closed Wiring
(EXAMPLE ONLY, SEE CONTROL PANEL INSTRUCTIONS)
B
DEOL Wiring
(EXAMPLE ONLY, SEE CONTROL PANEL INSTRUCTIONS)
C
Generic Control Panel
(SHOWS RESISTOR LOCATIONS)
3 7
Powering Up:
is ready to use.
3 8
3 9
The 10m Pet Lens.
Dimensions and Weight
Op cal and Range Features
Coverage
85 , 56 zones, and 6 planes
Maximum Range
10m
Op mal installa on Height
1.8-2.4m
Key Features
Animal immune
24kg
Blue Wave Technology
Yes
Automa c sensi vity
Yes
Digital temperature compensa on
Yes
DEOL resistors on board
Yes
Tamper protec on included
Yes
Power Supply
9-16 VDC (12VDC nominal)
Current Consump on at Rest
11mA
Current Consump on in Alarm
13mA
Relay Type
Solid state
Outputs Relay
60 VDC, 50mA protec on
Tamper Terminal
12 VDC max, 50mA max
Alarm Response
2.5 s
Detec on Speed
0.3 - 3m/s
Op cs
Sealed
Geometric Lens Configura on
3D
Other Details
Opera ng Temperature
-10°C to 40°C
Weight
125g
Dimensions(H x W x D)
117 x 69 x 50 mm
Accessories
Ceiling bracket Included
Yes
Wall Bracket Included
Yes
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
About this Manual
This manual is applicable to detector.
latest version in the company website
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
owners.
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
2011/65/EU.
1
START
C
D
s.
3
A
B
D
Hangzhou Hikvision Digital Technology CO.,Ltd.
2
PCB
A
B
B
LED ON
LED OFF
E
f) Back
Tamper
F
G
C
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
TAMPER
DEFAULT
PREDEFINITO
= =
AUTO HI
LOW AUTO
®
=
LOW AUTO
AUTO HI
C3
B
A
ALARM
6K8, 5K6,
4K7, 2K2, 1K
TAMPER
5K6, 4K7, 2K2, 1K
PIR
AUTO
+
+
+
+
HIGH /
LOW
The K
The KX
D
LOW
+
+
+
+
3
EOL
C
Publicité
Manuels Connexes pour HIKVISION DS-PD2-P10PE
Sommaire des Matières pour HIKVISION DS-PD2-P10PE
- Page 1 5K6, 4K7, 2K2, 1K Tamper EOL Resistor Headers: The DS-PD2-P10PE has 2 sets of header pins . These headers are used to select the End of Line resistance for EOL wiring applic a NOTE: If EOL wiring is not used, leave the headers OFF.
- Page 2 ALARM: ALARM TAMPER ALARM TAMPER TAMPER: ALARM TAMPER ALARM TAMPER 6K8, 5K6, TAMPER ALARM Control Panel Output ALARM Control Panel Output 5K6, 4K7, ALARM (0v in walk test) (0v in walk test) CONTROL 4K7, CONTROL 2K2, 2K2, PANEL PANEL ALARM TAMPER ALARM TAMPER...
- Page 3 Jumper resistenze EOL: l'unità DS-PD2-P10PE ha 2 set di pin di connessione. Questi Cabezales de resistencia de fin de línea (EOL, por sus siglas en inglés): El DS-PD2-P10PE Ces embases sont utilisées pour choisir la résistance en extrémité de ligne des applications Esses cabeçotes são usados para selecionar a resistência de fim de linha para aplicações de...
- Page 4 Opcje montażu Montageoptionen Варианты крепления Złącza rezystora EOL: Detektor DS-PD2-P10PE jest wyposażony w 2 złącza szpilkowe. Te Головки концевых резисторов: DS-PD2-P10PE имеет 2 набора штыревых перемычек. Эти Stiftleisten des EOL-Widerstands: Der DS-PD2-P10PE hat 2 Stiftleisten-Kontaktsets. Diese złącza umożliwiają wybór rezystora dla zastosowań z rezystorem na końcu linii (EOL).