Audio Settings; Network Settings - Samsung BD-E5400 Mode D'emploi

progressive mode
Lets you improve picture quality when viewing DVDs.
digital Output
Set the Digital Output to match the capabilities of the AV receiver you've connected to the
player : For more details, please refer to the Digital Output Selection table below.
digital Output Selection
Setup PCM
PCM Up to PCM 7.1ch
Dolby Digital PCM 2ch
Dolby Digital Plus PCM 2ch
Audio Stream
on Blu-ray Dolby TrueHD PCM 2ch
Disc
DTS PCM 2ch
DTS-HD Hi
PCM 2ch
Resolution Audio
DTS-HD Master
PCM 2ch
Audio
PCM PCM 2ch
Audio Stream
Dolby Digital PCM 2ch
on DVD
DTS PCM 2ch
Decodes the main feature
audio and BONUSVIEW
Definition for
Any audio stream together
Blu-ray Disc
into PCM audio and adds
Navigation Sound Effects.
10
02273B-BD-E5400-ZC-ENG.indd 10

Audio Settings

Bitstream
Bitstream
(Re-encoded
(Unprocessed)
DTS)
PCM DTS re-encoded
Dolby Digital DTS re-encoded
Dolby Digital Plus DTS re-encoded
Dolby TrueHD DTS re-encoded
DTS DTS re-encoded
DTS-HD Hi Resolution Audio DTS re-encoded
DTS-HD Master Audio DTS re-encoded
PCM 2ch PCM 2ch
Dolby Digital Dolby Digital
DTS DTS
Decodes the main
feature audio and
Outputs only the main feature
BONUSVIEW audio
audio stream so that your
stream together into
AV receiver can decode the
PCM audio and adds
audio bitstream.
Navigation Sound
You will not hear BONUSVIEW
Effects, then re-
audio or Navigation Sound
encodes the PCM
Effects.
audio into DTS
bitstream.
* If the Source Stream is 2ch, "Re-encoded
Dolby D" Setting is not applied. Output will
be PCM 2ch.
Blu-ray Discs may include three audio
streams :
- Main Feature Audio : The audio soundtrack
of the main feature.
- BONUSVIEW audio : An additional
soundtrack such as the director or actor's
commentary.
- Navigation Sound Effects : When you
choose a menu navigation selection, a
Navigation Sound Effect may sound.
Bitstream
Navigation Sound Effects are different on
(Re-encoded
each Blu-ray Disc.
Dolby D)
NOTE
✎
Re-encoded
Dolby Digital *
` Be sure to select the correct Digital Output or
Re-encoded
you will hear no sound or just loud noise.
Dolby Digital *
` If the HDMI device (AV receiver, TV) is not
Re-encoded
compatible with compressed formats (Dolby
Dolby Digital *
Digital, DTS), the audio signal outputs as PCM.
Re-encoded
Dolby Digital *
` Regular DVDs do not have BONUSVIEW audio
Re-encoded
and Navigation Sound Effects.
Dolby Digital *
` Some Blu-ray Discs do not have BONUSVIEW
Re-encoded
audio and Navigation Sound Effects.
Dolby Digital *
` If you play MPEG audio soundtracks, the audio
Re-encoded
Dolby Digital *
signal outputs as PCM regardless of your
PCM 2ch Digital Output selections (PCM or Bitstream).
Dolby Digital
pCm downsampling
DTS
Decodes the main
Lets you set 48kHz and 96kHz PCM down-
feature audio and
sampling on or off.
BONUSVIEW audio
stream together HdmI
into PCM audio and
adds Navigation
• If your TV is not compatible with
Sound Effects, then
compressed multi-channel formats (Dolby
re-encodes the PCM
Digital, DTS), the player may output PCM
audio into Dolby
2ch downmixed audio even though you
Digital bitstream or
selected Bitstream (either Re-encoded or
PCM.
Unprocessed) in the setup menu.
• If your TV is not compatible with PCM
sampling rates over 48kHz, the player may
output 48kHz downsampled PCM audio
even though you set PCM Downsampling
to Off.
dynamic Range Control
You can listen at low volumes, but still hear
dialog clearly.
This is only active if your player detects a
Dolby Digital signal.
downmixing mode
Select the Downmix method for stereo output.

Network Settings

Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic
- and most are - we recommend using the
Auto procedure for network setup. This is
easiest and will work in the majority of cases.
If it is static, you must use the manual set up
procedure. (See page 11.)
Network setup directions start below.
NOTE
✎
` This unit can only be connected to a Network
via a wireless connection.
Automatic Network Setup
1.
In the Home menu, press the ◄►
buttons to select Settings, and then
press the v button.
2. Press the ▲▼ buttons to select Network,
and then press the v button.
3.
Press the ▲▼ buttons to select
Network Setting, and then press the
v button. The Network Setting screen
appears.
2012-09-06 오후