Télécharger Imprimer la page
Masquer les pouces Voir aussi pour CDX-MP40:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

FM/AM
Compact Disc
Player
Installation/Connections
Installation/Connexions
CDX-MP40
Sony Corporation © 2003
1
1
2
4
5
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Front speaker
Haut-parleur avant
Rear speaker
Haut-parleur arrière
Power amplifier
Amplificateur de puissance
3-251-806-11 (1)
Printed in Korea
3
× 4
× 2
CD/MD changer
Changeur de CD/MD
Rotary commander RM-X4S
Satellite de commande RM-X4S
2
A
AUDIO OUT FRONT
AUDIO OUT REAR
B
BUS AUDIO IN
BUS CONTROL IN
Source selector*
Sélecteur de source*
XA-C30
Cautions
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected wires
with electrical tape for safety.
• The use of optical instruments with this product
will increase eye hazard.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit's rating must be higher than the sum of
each component's fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
• The numbers in the list are keyed to those in the
instructions.
• The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar 3
from the unit. For details, see "Removing the
protection collar and the bracket (4)" on the
reverse side of the sheet.
• Keep the release keys 5 for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
Catch
Note
Before installing, make sure that the catches on both
sides of the bracket 1 are bent inwards 2 mm (
3
/
32
the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
BUS AUDIO IN
BUS CONTROL IN
* not supplied
non fourni
Connection example (2)
Notes (2-A)
• Be sure to connect the ground cord before connecting
the amplifier.
• If you connect an optional power amplifier and do not
use the built-in amplifier, the beep sound will be
deactivated.
Tip (2-B-
)
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (3)
1
To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no
power antenna or antenna booster, or with a
manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see "Notes on the control and
power supply leads."
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the +12
V power (battery) terminal which is energized at
all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see "Notes on the control and
power supply leads."
6
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/
side glass, connect the power antenna control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.
• A power antenna without relay box cannot be used
in). If
with this unit.

Publicité

loading

Sommaire des Matières pour Sony CDX-MP40

  • Page 1 Source selector* Sélecteur de source* XA-C30 BUS CONTROL IN CDX-MP40 * not supplied non fourni Sony Corporation © 2003 Printed in Korea Cautions Connection example (2) • This unit is designed for negative ground 12 V DC Notes (2-A) operation only.
  • Page 2 Source selector (not supplied) Supplied with the CD/MD changer Sélecteur de source Fourni avec le changeur de CD/MD (non fourni) XA-C30 Supplied with XA-C30 Fourni avec le XA-C30 AUDIO OUT REMOTE FRONT BUS AUDIO IN from car antenna AUDIO AUDIO à...
  • Page 3 Orient the release key Face the hook inwards. correctly. Tournez le crochet vers Orientez correctement l’intérieur. la clé de déblocage. Dashboard Tableau de bord 1 8 2 5 3 m Claws Griffes TOYOTA NISSAN max. size max. size 5 × 8 mm 5 ×...
  • Page 4 •Avoid installing the unit in areas subject to •Evitez d’installer l’appareil dans un endroit your Sony dealer. cas, votre détaillant Sony. dust, dirt, excessive vibration, or high exposé à la poussière, à la saleté, à des temperatures, such as in direct sunlight or near vibrations excessives ou à...