Preparation; Service Points; Fuel Filter; Tyre Pressure - Stiga Titan Mode D'emploi

All manuals and user guides at all-guides.com
GB
• Clean the engine's radiator (13:D) and oil cool-
er (13:E) with a soft brush. Large objects can be
removed by hand. If the radiator or cooler is
heavily soiled, use lightly running water with a
suitable detergent.
Never use high-pressure water or air against
the radiator fins. This will damage the fin
structure.
6 MAINTENANCE
6.1 Service program
In order to keep the machine in good condition, as
regards reliability and operational safety as well as
from an environmental perspective, the service in-
structions in this section should be followed.
All services should be carried out by authorised
workshops.
Service, carried out by authorised workshops,
guarantees a professional job with original re-
placement parts.
The service log should be stamped at every service
carried out by an authorised workshop. A "fully
stamped" service log is a valuable document that
improves the machine's second-hand value.
The service points are given in the table below. De-
scriptions of how the procedures are to be carried
out are given after the table.

6.2 Service points

.
1st time Interval
Hours of operation/
Service point
Calendar months
Water separator,
check
Pre-filter, cleaning
Fuel filter, replace 400/-

Tyre pressure,

check, adjust
Engine oil, filter,
50/12 200/12
change
Hydraulic oil, fil-
50/12 400/12
ter, change/clean
Wheel motors ,
50/12 200/12
change oil
Belt transmissions,
50 200/-
check
Cooling system,
1000/12
clean
Battery, check
Air filter, clean pre-
filter
Air filter, change
inner filter
Lubrication
Adjusting valves 1000/-
Grinding valves 2000/-
84
ENGLISH

6.3 Preparation

All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by
always applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by removing the ignition key.
6.4 Water separator
There is a float in the water separator (15:E) that
can be viewed through the transparent cup. The
float must be at the bottom. If the float has risen,
the water separator must be cleaned as follows:
1. Shut off the water separator tap. See fig. 15.
2. Hold a container under the water separator to
collect fuel.
3. Open the cup by pressing its ring (15:A).
4. Carefully remove the cup (15:B) and remove
the spring (15:D) and float (15:E) from the cup.
5. Clean the inside of the cup and thread filter
(15:C).
6. Check that the O-ring is intact and reinstall the
components in reverse order.
7. Open the tap.
8. Bleed the fuel system. See "5.13".
See
Clean the fuel tank if water accumulates in the wa-
para-
ter separator often. Contact an authorised work-
graph
shop.
50/- 6.4

6.5 Fuel filter

6.4
1. Shut off the fuel filter's tap. See fig. 14.
6.5
2. Hold a container under the fuel filter to collect
6.6
fuel.
3. Detach the cup by turning its ring (14:J).
6.7
4. Carefully remove the cup (14:H) and remove
the filter (14:F).
6.8
5. Clean the inside of the cup (14:H).
6.9
6. Check that the O-ring (14:G) is intact and rein-
stall the components with new filter in reverse
6.10
order.
7. Open the tap.
6.11
8. Bleed the fuel system. See "5.13".
50/- 6.12
6.6 Tyre pressure
6.13
Set the tyre pressures to their default pressures.
Pressure front and rear: 0.9 bar.
6.13
See pressures in the manual for relevant imple-
6.14
ment.
6.15
6.15