Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

This is a legacy product document
supported by Resideo. It is no
longer manufactured
HE360A,B
Powered Flow-Through Humidifier
APPLICATION
The HE360A,B Powered Flow-Through Humidifier works with the
warm air furnace blower to provide humidification for the whole
house.
INSTALLATION
When Installing this Product...
1. Read these instructions carefully. Failure to follow them could
damage the product or cause a hazardous condition.
2. Check the ratings given in the instructions and on the product to
make sure the product is suitable for your application.
3. Installer must be a trained, experienced service technician.
4. After installation is complete, check out product operation as
provided in these instructions.
CAUTION
Personal Injury or Equipment Hazard.
Improper drilling can cause equipment damage or
personal injury.
• Do not cut or drill into any air conditioning or electrical
accessory.
CAUTION
Property or Equipment Hazard.
Can cause property or equipment damage.
• Locate the humidifier where the ambient temperature is
between 32°F (0°C) and 160°F (71°C) or property damage
can occur.
• Do not install humidifier where freezing temperatures could
occur.
• Be sure supply plenum static pressure is no greater than
0.4 in. wc and water pressure is no greater than 125 psi.
IMPORTANT
• Mount the humidifier at least 3 in. (76 mm) above the
furnace jacket to allow adequate space for the drain line.
Check that there is adequate space above the humidifier to
remove and install the humidifier cover. Do not install on a
furnace jacket.
1. Determine the best location for the humidifier and draw a level
line on the plenum. See Fig. 1 and 2.
IMPORTANT
To assure optimal product performance, be sure the
template is level before marking.
2. Tape the template in position and trace around the template.
3. Remove the template and carefully cut the rectangular opening.
4. Loosen the thumbscrew on the bottom of the humidifier and
remove the cover.
5. Remove the humidifier pad assembly by grasping the top of the
tray and pulling the assembly out of the housing. See Fig. 3.
6. Position the securing clips as shown in Fig. 4.
Template (entire sheet). Top of Humidifier
USE THIS TEMPLATE WHEN INSTALLING THE HE360 HUMIDIFIER
SEE 69-1176EF OWNER'S GUIDE
READ AND SAVE THESE INSTRUCTIONS
T A L
O N
R IZ
H O
T U
R E
R N
T U
R N
R E
T U
R E
O Y
W B
L O
Fig. 1. Typical humidifier installation locations.
Fig. 2. HE360 Humidifier location in relation to air conditioning
cooling coils.
FEED TUBE NOZZLE
WATER
DISTRIBUTION TRAY
HUMIDIFIER
PAD ASSEMBLY
THUMB
SCREW
Fig. 3. Humidifier components.
Template (entire sheet)
R N
T U
R E
R N
O Y
H B
H I G
W N
7. Position the humidifier housing in the hole (be sure it is level),
D O
O
F L
so the locking tabs are in place on the upper and lower sheet
metal edge of the hole.
8. Push in securing clips until completely seated.
9. Drill holes and install the three sheet metal screws at the top of
the humidifier housing. Secure the housing with the three
remaining screws.
10. Reinstall the humidifier pad assembly in the humidifier housing.
M12808B
IMPORTANT
For proper operation, be sure the mark on the end of the
humidifier pad is facing up. Check that the water feed tube is
placed in the guide slots of the humidifier housing.
11. Hook the top of the cover to the housing and secure with the
thumbscrew located at the bottom of the cover.
WIRING
WARNING
Serious Personal Injury or Equipment Hazard.
Moving parts can cause electrical shock and injury.
• Disconnect power supply before installation or servicing.
M12812B
• This device contains a moving fan blade; do not operate the
humidifier without the cover securely attached.
All wiring must comply with applicable local codes, ordinances and
regulations.
H8908 Humidistat Wiring Connections
IMPORTANT
• Select models of fan centers include humidifier taps so the
current sensing relay or sail switch is not needed.
• If not using a current sensing relay or sail switch, the 120V
humidifier plug must be energized during blower motor
cycles for proper operation.
1. Wire the current sensing relay or sail switch.
2. Connect only the two yellow wires to the humidistat (red wire
connections are not used for mechanical humidistats). See the
typical wiring diagrams in Fig. 5 through 7.
For additional mounting and wiring information, refer to the humidistat
installation instructions.
HUMIDIFIER
HOUSING
COVER
ASSEMBLY
M12809
INSTALLATION INSTRUCTIONS
CLIP
CLIP
M12813A
Fig. 4. Position securing clips.
Put Bar Code Here
69-1175EF—05

Publicité

loading

Sommaire des Matières pour Honeywell HE360A

  • Page 1 USE THIS TEMPLATE WHEN INSTALLING THE HE360 HUMIDIFIER SEE 69-1176EF OWNER’S GUIDE READ AND SAVE THESE INSTRUCTIONS APPLICATION CLIP CLIP The HE360A,B Powered Flow-Through Humidifier works with the warm air furnace blower to provide humidification for the whole T A L house. R IZ INSTALLATION...
  • Page 2 Template (entire sheet), Top of Humidifier HE360A,B POWERED FLOW-THROUGH HUMIDIFIER NOTE: Lightly clean the copper tubing ends with fine sandpaper before making any connections. TO BLOWER MECHANICAL MOTOR HUMIDISTAT IGNITION BOX 2. Use 1/4 in. O.D. copper tubing and connect the saddle valve to...
  • Page 3 LIRE ET CONSERVER CES INSTRUCTIONS. APPLICATION PINCE DE FIXATION PINCE DE FIXATION T O U L'humidificateur à circulation directe motorisé HE360A,B fonctionne avec le ventilateur du système de chauffage à air chaud pour assurer N T A IZ O H O R l’humidification de l’air dans toute la maison.
  • Page 4 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limitée ® Marque de commerce déposée aux É.-U. 35, Dynamic Drive © 2010 Honeywell International Inc. Tous droits réservés Toronto (Ontario) M1V 4Z9 69-1175EF—05 K.K. Rev. 02-10 Imprimé aux États-Unis customer.honeywell.com...

Ce manuel est également adapté pour:

He360b