Whirlpool WTW6700TW0 Mode D'emploi page 2

FOR SERVICE TECHNICIAN ONLY – DO NOT REMOVE OR DESTROY
If no indicators come on after pressing POWER
button, go to TEST #1, page 4.
Indication 2: Fault code flashes from the
display.
Action:
Review the Display Fault/Error Codes table,
page 3, for the recommended procedure.
DIAGNOSTIC: Saved Fault Codes
If there are saved fault codes (as indicated in step 3 of
Activation of Automatic Diagnostic Test Mode, page 1),
the most recent fault code will be displayed and
alternately show "F" and "XX" where XX is the fault
code, and all the cycle selector indicators flash.
Press and release
the same button Second most recent fault code is
used to activate
displayed.
Diagnostics
Third most recent fault code is
Repeat
displayed.
Fourth most recent fault code is
Repeat
displayed.
All indicators momentarily turn
Repeat
off, then stay on. After 5 seconds,
Automatic test cycle begins.
NOTE: Fault codes are retained.
ACTIVATION OF MANUAL DIAGNOSTIC
TEST MODE
1. Carefully read and perform steps 1 and 2 under
Activation of Automatic Diagnostic Test Mode,
page 1, and press the same button once during the
88
5 second display time of the .
NOTE: If the button is not pressed within 5 seconds,
the Automatic test will start (after saved fault codes).
2. If done successfully, a single beep occurs and the
two-digit display shows the control ID# (
etc.) for 3 seconds, then displays
Garment indicator LED flashes. See Diagnostic:
Manual, below.
DIAGNOSTIC: Manual
Enter Manual Diagnostic test mode, above. Two-digit
00
display shows , and Add A Garment indicator LED is
flashing.
NOTE: If there is no activity (button press, cycle select)
within 5 minutes, the control automatically exits
Diagnostic mode and enters standby mode.
Manual: Water Valves
(See Manual Activation,
above)
To check FRESH valve
select or press the following:
WHITEST WHITES START (turns on Fresh valve,
cycle indicator flashes) WASH/RINSE TEMP
(enables fill of Hot, Warm, Cool or Cold, or no water
according to WASH/RINSE TEMP selection and
indicator) START (turns off Fresh valve, cycle
indicator is steady on).
To check DETERGENT valve
select or press the
following:
HEAVY DUTY START (turns on Detergent valve,
cycle indicator flashes) WASH/RINSE TEMP
(enables fill of Hot, Warm, Cool or Cold, or no water
according to WASH/RINSE TEMP selection and
indicator) START (turns off Detergent valve, cycle
indicator is steady on).
To check FABRIC SOFTENER valve
the following:
NORMAL START (turns on Fabric Softener valve,
cycle indicator flashes) WASH/RINSE TEMP
(enables fill of Hot, Warm, Cool or Cold, or no water
PART NO. W10026628A
according to WASH/RINSE TEMP selection and
indicator)
cycle indicator is steady on).
To check BLEACH valve
CASUAL
water, cycle indicator flashes)
Bleach valve, cycle indicator is steady on).
NOTE: Washer can only fill cold through Bleach valve.
If any valve fails to turn on go to TEST #2, page 4.
Manual: Pumps
Models with Push-button cycles:
Press and release:
CLEAN WASHER,
DRAIN & SPIN or
RINSE/DRAIN & SPIN
Repeat
Repeat
Repeat
Models using Cycle Selector:
Select CLEAN WASHER or DRAIN & SPIN.
Press and release:
START
Repeat
Repeat
Repeat
If pumps fail to turn on, go to TEST #7, page 5.
Manual: Lid Switch
08 09
, ,
at left)
00
and the Add A
Opening the lid should cause the Clothes Clean or Done
status indicator to turn off. Closing the lid should cause
the indicator to turn on.
If Clothes Clean or Done indicator does not turn
off or on, go to TEST #8, page 6.
Manual: Lid Lock
NOTE: Lid must be closed. If lid is not closed, an invalid
button press beep will occur when performing next step.
Press and release:
2nd RINSE or
EXTRA RINSE
Repeat
If lid does not lock or unlock, go to TEST #8,
page 6.
Manual: Motor
Rotor Position Sensor (RPS):
and Spin indicators to detect the three hall sensors.
Console may have up to two of these indicators on at
one time when the basket is not moving. Open lid
and rotate basket by hand. The Wash, Rinse and Spin
status indicators should toggle on and off according
to direction the basket is being turned.
If none of these indicators are on go to TEST #3,
page 4.
Spin:
To activate Spin, lid must be closed with lid lock
enabled. See Manual: Lid Lock test, above.
select or press
NOTE: If lid is not closed, an invalid button press
beep will occur when performing next step.
POUR LE TECHNICIEN SEULEMENT – NE PAS ENLEVER NI DÉTRUIRE
START (turns off Fabric Softener valve,
select or press the following:
START (turns on Bleach valve with cold
START (turns off
(See Manual Activation, at left)
Turns on recirculation pump,
button indicator is steady on.
Turns off recirculation pump,
button indicator turns off.
Turns on drain pump, button
indicator flashes.
Turns off drain pump, button
indicator turns off.
Turns on recirculation pump,
cycle indicator is steady on.
Turns off recirculation pump,
cycle indicator is steady on.
Turns on drain pump, cycle
indicator flashes.
Turns off drain pump, cycle
indicator is steady on.
(See Manual Activation,
(See Manual Activation, at left)
Lid locks, Lid Lock indicator
turns on.
Lid unlocks, Lid Lock
indicator turns off.
(See Manual Activation, at left)
Uses Wash, Rinse
PAGE 2
Press and
release:
SPIN SPEED,
Motor/basket spins at 23 rpm.
WATER LEVEL
or LOAD SIZE
Repeat
Motor/basket spins at 530 rpm.
Motor/basket spins at ≥ 950 rpm.
Repeat
Repeat
Motor turns off.
NOTE: Indicators above button scroll from top to
bottom.
If motor fails to spin, go to TEST #3, page 4.
Agitate:
Water must cover the wash plate (or agitator
vanes) to ensure the basket is floating prior to
agitation. Enabling agitation without enough water
may cause a fault condition to occur. See Manual:
Water Valves test, at left.
Press and release:
Gentle wash action.
SOIL LEVEL
Repeat
Normal wash action.
Repeat
Heavy wash action.
Repeat Motor turns off.
NOTE: Indicators above button scroll from top to
bottom.
If motor fails to agitate, go to TEST #3, page 4.
ACTIVATION OF CONSOLE AND
INDICATORS DIAGNOSTIC TEST MODE
This test checks the cycle selector knob, indicators,
buttons, two-digit display and beeper.
1. Plug in washer or reconnect power.
2. From Standby (Off) Mode press and release
(key-dance) the following buttons within 4 seconds:
SOIL WASH/RINSE SOIL
LEVEL TEMP LEVEL
If successful, two-digit will display and you will
have 5 seconds to complete next step.
3. Within 5 seconds of showing in display, press
START (all indicators in display are illuminated and
88
is displayed.
Press START a second time. This turns off status
indicators and two-digit display (all other
indicators remain illuminated).
Press START a third time. This turns on status
indicators and two-digit display (all indicators are
illuminated).
4. Rotate WASH CYCLE selector back and forth.
Indicators will toggle on (or off).
5. Press buttons to verify function. Indicators will toggle on
(or off) and beep tone will sound when buttons are
pressed.
NOTE: Pressing SOIL LEVEL, SPIN SPEED, WATER
LEVEL or LOAD SIZE, and WASH/RINSE TEMP will cause
all indicators above these buttons to toggle on (or off) at
one time.
If any of the following occur during steps above, see
TEST #4, page 5:
None of the indicators light up
No beep sound is heard
Some buttons do not light indicators
DEACTIVATION OF DIAGNOSTIC
TEST MODE
Press the STOP or PAUSE/CANCEL or POWER button at
any time to exit Automatic, Manual, or Console &
Indicators diagnostic test modes.
PIÈCE N
WASH/RINSE
TEMP
o
W10026628A