Table des Matières
Publicité
SM 2610947705 7-09:SM 2610947705 11-06 7/9/09 2:13 PM Page 52
Non Thru-Sawing
Add 8" high flat facing board to the fence, the full length of the
fence (Fig. 46).
Use featherboards for all "Non Thru-Sawing" operations (when
sawblade guard must be removed). Featherboards 1 are used to
keep the work in contact with the fence and table as shown, and to
stop kickbacks.
Mount featherboards 1 to fence and table as shown, so that
leading edges of featherboards will support workpiece until cut is
complete, and the workpiece has been pushed completely past the
cutter (sawblade, dado head, molding head, etc.) with a Push Stick
2, as in ripping.
Before starting the operation (switch "OFF" and cutter below table
surface):
A. Install featherboards so they exert pressure on the workpiece;
be positive they are securely attached.
B. Make sure by trial that the featherboards will stop a kickback if
one should occur.
Featherboards are not employed during non thru-sawing
operations when using the miter gauge.
Replace the sawblade guard as soon as the non thru-sawing
operation is complete.
RABBETING is known as cutting out a section of the corner of a
piece of material, across an end or along an edge (Fig. 47).
Making a RABBET requires cuts which do not go all the way
through the material. Therefore the blade guard must be removed.
1. Remove blade guard.
2. For rabbeting along an edge (long way of workpiece) as shown,
add facing to rip fence approximately as high as the workpiece is
wide. Adjust rip fence and blade to required dimensions; then make
first cut with board flat on table, follow set-up Fig. 46. Make second
cut with workpiece on edge, follow set-up Fig. 44. Follow all
precautions, safety instructions, and operation instructions as for
ripping or rip type operations, including featherboards and Push
Stick, etc.
3. For rabbeting across an end, for workpiece 10-1/2" and narrower
make the rabbet cut with the board flat on the table. Using the miter
gauge fitted with a facing, follow the same procedures and
instructions for crosscutting making successive cuts across the
width of the workpiece to obtain the desired width of cut. DO NOT
use the rip fence for rabbeting across the end.
4. INSTALL BLADE GUARD IMMEDIATELY UPON COM-
PLETION OF RABBETING OPERATION.
Rabbet cuts can also be made in one pass of the workpiece over
the cutter using the dado head or molding head.
Dado Cutting
Instructions for operating the Dado blade set are contained in
booklet furnished with this accessory.
The recommended Dado blade set is listed under Accessories on
Page 56 & 57. Maximum dado width capacity for the 6" dado set is
1/2". When assembling dado set, do not use the outer blade
washer.
ALWAYS USE APPROPRIATE TABLE INSERT LISTED UNDER
ACCESSORIES.
Rabbeting
FIG. 46
"C" CL MPS
SERRE-JOINTS EN C
WORK
SUPPORT
BR Z DER S EN "C"
SUPPORT
POYO DE L
PIEZ DE
TR B JO
1
FIRST CUT
PREMIÈRE COUPE
FIG. 47
PRIMER CORTE
R BBET
FEUILLURE
REB JO
SECOND CUT
DEUXIÈME COUPE
SEGUNDO CORTE
R BBETING LONG
THE EDGE
RÉ LIS TION D'UNE
FEUILLURE LE LONG D'UN
BORD
REB JO LO L RGO
DEL BORDE
52.
1
2
R BBETING CROSS
THE END
RÉ LIS TION D'UNE
FEUILLURE EN TR VERS
D'UNE EXTRÉMITÉ
REB JO TR NSVERS L
L EXTREMO
Publicité
Chapitres
Table des Matières
