Makita LS003G Manuel D'instructions page 30

Dust bag
CAUTION:
When performing a cutting, always
attach the dust bag or connect a vacuum cleaner
to prevent dust-related hazards.
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, remove
the dust extraction hose from the tool and connect the
dust bag to the dust nozzle (upper dust port).
► Fig.44: 1. Dust extraction hose 2. Dust bag 3. Dust
nozzle (upper dust port)
When the dust bag is about half full, remove the dust
bag from the tool and pull the fastener out. Empty
the dust bag of its contents, tapping it lightly so as to
remove particles adhering to the insides which might
hamper further collection.
► Fig.45: 1. Fastener
Securing workpiece
WARNING:
It is extremely important to always
secure the workpiece correctly with the proper
type of vise or crown molding stoppers. Failure to
do so may result in serious personal injury and cause
damage to the tool and/or the workpiece.
WARNING:
When cutting a workpiece that
is longer than the support base of the miter saw,
support the entire length of the material beyond
the support base keeping the material level.
Proper workpiece support helps to avoid blade pinch
and possible kickback which may result in serious
personal injury. Do not rely solely on the vertical
vise and/or horizontal vise to secure the workpiece.
Thin material tends to sag. Support workpiece over
its entire length to avoid blade pinch and possible
KICKBACK.
► Fig.46: 1. Support 2. Turn base
Guide fences
WARNING:
Before operating the tool, make
sure that the upper fence is secured firmly.
WARNING:
Before bevel-cutting, make sure
that no part of the tool, especially the saw blade,
contacts the upper and lower fences when fully
lowering and raising the handle in any position
and while moving the carriage through its full
range of travel. If the tool or blade makes contact
with the fence, this may result in kickback or unex-
pected movement of the material and serious per-
sonal injury.
Use upper fences to support the material higher than
the lower fences. Insert the upper fence into the hole on
the lower fence and tighten the clamping screw.
► Fig.47: 1. Upper fence 2. Lower fence 3. Clamping
screw 4. Adjusting screw
NOTICE:
The lower fences are fixed to the base
in the factory. Do not remove the lower fences.
NOTICE:
If the upper fence is still loose after
tightening the clamping screw, turn the adjusting
screw to close a gap. The adjusting screw is factory
adjusted. You don't need to use it unless needed.
When not using the upper fence, you can store it onto
the pipe of the sub base. Use the clip on the upper
fence to hold it on the pipe of the sub base.
► Fig.48: 1. Sub base 2. Upper fence 3. Clip
Vertical vise
WARNING:
firmly against the turn base and guide fence with
the vise during all operations. If the workpiece is
not properly secured against the fence, the material
may move during the cutting operation causing pos-
sible damage to the saw blade, causing the material
to be thrown and loss of control resulting in serious
personal injury.
The vertical vise can be installed into either the left or
right side of the base and sub base. Insert the vise rod
into the hole in the base or sub base.
► Fig.49: 1. Vertical vise 2. Hole for vertical vise
3. Sub base 4. Base
► Fig.50: 1. Vise arm 2. Vise rod 3. Clamping screw
4. Vise knob
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the screw. If the clamping screw contacts the
carriage, install the vertical vise to the sub base or the
opposite side on the base. Make sure that no part of the
tool contacts the vise when lowering the handle all the
way. If some part contacts the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
NOTE: For a quick setting of workpiece, turning the
vise knob to 90° counterclockwise allows the vise
knob to be moved up and down. To secure the work-
piece after setting, turn the vise knob clockwise.
Horizontal vise
Optional accessory
WARNING:
wise until the workpiece is properly secured. If
the workpiece is not properly secured, the material
may move during the cutting operation causing pos-
sible damage to the circular saw blade, causing the
material to be thrown and loss of control resulting in
serious personal injury.
WARNING:
such as base boards, against the fence, always
use the horizontal vise.
CAUTION:
When cutting the workpiece of the
thickness 20 mm or thinner, make sure to use a
spacer block to secure the workpiece.
30 ENGLISH
The workpiece must be secured
Always rotate the vise nut clock-
When cutting a thin workpiece,