Bosch Professional GWS 6-100 Instructions D'emploi page 6

2 609 140 063 - Buch Seite 2 Mittwoch, 11. Februar 2004 10:03 10
Operating Controls
The numbering of the machine elements refers to
the representation of the machine on the graph-
ics page.
While reading the operating instructions, unfold
the graphics page for the machine and leave it
open.
1 Speed selector thumbwheel (GWS 6-100 E,
GWS 6-115 E, GWS 8-100 CE,
GWS 8-115 CE, GWS 8-125 CE)
2 On/Off switch
3 Auxiliary handle
4 Spindle locking button
5 Grinder spindle
6 Protective hood
7 Screw
8 Retainer mounting flange
(for the M 14 grinding spindle with O-ring)
9 Grinding-/cutting disc*
10 Clamping nut
11 Quick clamping nut*
(for M 14 grinder spindle)
12 Hand protector*
13 Rubber sanding plate*
14 Sanding sheet*
15 Round nut*
16 Cup brush*
17 Retainer mounting flange M 10
* Not all the illustrated or described accessories are
included as standard delivery.
Noise/Vibration Information
Measured values determined according to
EN 50 144.
The A-weighted noise levels of the tool are typi-
cally: Sound pressure level: 89 dB (A); sound
power level: 102 dB (A).
Wear ear protection!
The weighted acceleration is typically 5.0 m/s
Intended Use
The machine is intended for cutting, roughing and
brushing metal and stone materials without using
water. For cutting stone, a cutting guide is re-
quired.
Electronically-controlled machines can be used
for sanding and polishing with the approved
sanding tools.
7 • 2 609 140 063 • TMS • 04.02.04
All manuals and user guides at all-guides.com
Information on Statics
Slots in load-carrying walls are subject to Part 1
of
No. 1053, or to country-specific regulations.
These regulations are to be observed under all
circumstances. Before beginning work, consult
the structural engineer, architect or construction
supervisor in charge.
2
.
English - 2
the German Industrial
For Your Safety
Working safely with this ma-
chine is possible only when the
operating and safety information
is read completely and the in-
structions contained therein are
strictly followed. In addition, the
general safety notes in the en-
closed booklet must be ob-
served. Before using for the first
time, ask for a practical demon-
stration.
Wear protective glasses and ear protection.
Wear additional protection equipment for your
safety, such as protective gloves, sturdy
shoes, hard hat and apron.
The dust generated during working can be det-
rimental to health, inflammable or explosive.
Suitable safety measures are required.
For example: Some types of dust are sus-
pected of being carcinogenic. Use suitable
dust-/chip extraction and wear a dust mask.
Dust from light alloys can burn or explode. Al-
ways keep the workplace clean, as mixtures of
materials are particularly dangerous.
If the cable is damaged or cut through while
working, do not touch the cable and pull the
plug immediately. Never use the machine if the
cable is damaged.
Connect machines that are used in the open
via a residual current device (RCD) with an ac-
tuating current of 30 mA maximum. Do not op-
erate the machine in rain or moisture.
When working with the machine, always hold it
firmly with both hands and make sure you are
in a secure standing position.
Secure the workpiece. Clamping devices or a
vise will hold the workpiece in place better than
the hand.
Always direct the cable to the rear away from
the machine.
Always switch the machine off and wait until it
has come to a standstill before placing it down.
Standard (DIN)