Additional Safety Instructions - YATO YT-82020 Manuel

GB
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are
tired or under eff ects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries. Always
use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks, protec-
tive shoes, helmets and hearing protections permits to reduce the risk of serious injuries. Avoid accidental activation of the
tool. Make sure the switch is in the OFF position, before you connect the tool to the mains. Holding the tool with a fi nger
on the switch or connecting an electric tool when the switch is in the ON position may lead to serious injuries. Before you turn an
electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner left on rotating
elements of the tool may lead to serious injuries. Keep your balance. Maintain an appropriate position. It will permit to control
the electric tool in case of unpredicted situations during its operation. Use protective clothes. Do not wear loose clothes or
jewellery. Keep your hair, clothes and gloves away from moving elements of the electric tool. Loose clothes, jewellery or
long hair may get caught on moving elements of the tool. Use dust extractors or dust containers, if the tool is equipped with
any. Make sure they are properly connected. Using of dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the given work
will result in a more effi cient and safer work. Do not use the electric tool if the switch is not functioning properly. A tool which
may not be controlled by means of a switch is dangerous and must be repaired. Disconnect the plug from the mains socket
before any adjustment, replacement of accessories or storage of the tool. It will permit to avoid accidental activation of the
electric tool. Store the tool away from children. Do not allow untrained persons to operate the tool. An electric tool may be
dangerous in hands of an untrained person. Make sure the tool is properly maintained. Check the tool in order to detects
any unfi tting or loose moving elements. Check whether the elements of the tool are not damaged. In case any damaged
elements of the tool are detected, they must be repaired before the electric tool is operated. Many accidents are caused
by improper maintenance of tools. Cutting tools must be sharp and clean. Properly maintained cutting tools are easier to
control during work. Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool
in accordance with its purpose, taking into account the kind and conditions of work. Should the tool be used for other ap-
plications than the ones it has been designed for, the risk of a dangerous situation increases.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee
a proper level of safety of operation of the electric tool.

ADDITIONAL SAFETY INSTRUCTIONS

While using the tool, it is required to observe at all times the recommendations indicated in the manual as well as other safety
recommendations.
The tool must not be exposed to precipitations.
Make always sure the power supply voltage corresponds to the value indicated in the rating plate of the tool.
Before you proceed to operate the tool, make sure the wrench sockets to be used are not damaged. In case any damage has been
detected, the sockets must be immediately replaced.
Socket head wrenches and other inserted tools must be adequate for operation with pneumatic tools. The sockets and other
inserted tools must be in good working order, clean and undamaged, and their sizes must be appropriate for the size of the drive.
It is prohibited to modify the wrench sockets or the drive.
During work it is always required to wear protective goggles, and it is recommended to wear gloves and protective clothes.
During work the wrench must be always held with both hands.
OPERATION OF THE WRENCH
ATTENTION! Installation of accessories may be realises only when the power supply voltage is off . Remove the plug of the
power supply cord of the tool from the mains socket!
Work with impact socket head wrenches
Before you start turning bolts or nuts with a socket head wrench, place the bolt or nut manually on the thread (at least two turns).
Make sure the size of the socket head wrench has been selected correctly in relation to the element to be tightened or undone.
Incorrect size may be a cause of damage both to the wrench and the nut or the bolt.
Tightening and undoing bolts and nuts
Install an adequate socket head impact wrench on the drive (II)
Connect the tool to the mains.
Grab the tool with both hands. (III)
Place the socket head wrench on the nut or bolt head.
O R I G I N A L I N S T R U C T I O N S
11