Accessories - Milwaukee 2445-20 Manuel De L'utilisateur

Locking the trigger
To lock the trigger, push the trigger lock from the
lock side of the tool. The trigger will not work while
the switch is in the locked position. Always lock the
trigger and remove the battery pack before perform-
ing maintenance and changing accessories. Lock
the trigger when storing the tool and when the tool
is not in use.
To unlock the trigger, push the trigger lock from the
unlock side of the tool.
To reduce the risk of injury, do not
WARNING
start the tool with the blade con-
tacting the workpiece.
Be sure the blade always extends beyond the
shoe and workpiece throughout the stroke.
Blades may shatter if they impact the workpiece.
Making the Cut
1. Position the tool with the front part of the shoe on
the workpiece and start the tool.
2. Hold the shoe firmly against the workpiece and
guide the tool along the desired cutting line. Do not
feed into the work too hard, light pressure on the
saw blade will achieve the optimum cutting speed.
Special Cutting Techniques
1. Straight cuts — To obtain a perfectly straight cut,
clamp a strip of wood as a guide along the work-
piece or use a rip guide.
2. Bevel cuts — adjust the shoe to the correct angle
(see Adjusting the Shoe).
3. Cutting Sheet Metal — sheet metal may vibrate
when being cut. To minimize vibration clamp, the
workpiece to a wood base.
To reduce the risk of explosion,
WARNING
electric shock and property dam-
age, always check the work area for hidden gas
pipes, electrical wires or water pipes when mak-
ing blind or plunge cuts.
Plunge Cutting
Plunge cuts can be made into
soft materials without a pre-
drilled hole. Harder mat-
erials require a starter hole
with a diameter slightly over
the width of the blade. To
make a plunge cut:
1. Make sure nothing below
the intended cut area will
be damaged.
All manuals and user guides at all-guides.com
2. Without turning the tool on,
3. Align the blade with the
4. Using the front edge of
5. When the shoe is flat
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest service center.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
5
place the front edge of
the shoe solidly on work-
piece.
intended cut line, but
keep it above the work-
piece.
the shoe as a pivot, turn
on the tool and gradually
lower the blade into the
workpiece.
against the workpiece,
normal cutting may take
place.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
Maintaining Tool
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
Cleaning
Repairs

ACCESSORIES

Use only recommended accesso-
WARNING
ries. Others may be hazardous.