Changing The Vfp Setting - JVC TH-V70 Manuel D'instructions

Changing the VFP setting

The VFP (Video Fine Processor) function enables you to
adjust the picture character according to the type of
programming, picture tone or personal preferences.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
AUX FM/AM
AUDIO ANGLE
RETURN DIGEST
TOP MENU MENU
–
CONTROL SUBWOOFER
1
VCR
–
CENTER
TV 4
–
SLEEP
REAR-L
7
–
SETTING REAR-R
10
TV RETURN
ON
SCREEN
CHOICE
TV VOL CHANNEL
7 During playback
1 Press VFP (PROGRESSIVE).
The current VFP settings appear on the TV.
Example: When "NORMAL" is selected.
2 Press Cursor 3/2 repeatedly to select the
VFP mode.
Each time you press the button, the VFP mode changes
as follows.
" NORMAL " CINEMA " USER 1 " USER 2
" (back to the beginning)
• NORMAL:
• CINEMA:
• USER 1 and USER 2: You can adjust parameters that
NOTE:
You cannot adjust "NORMAL" and "CINEMA."
VIDEO
DVD
CD
TV AUDIO
DVD
VCR 1 VCR
DECODE
SUBTITLE
ZOOM VFP
VFP
+
PROGRESSIVE
ZOOM
(PROGRESSIVE)
–
SOUND
button
+
EFFECT
2 3
+
TEST
5 6
+
8 9
+
0 +10
FM MODE 100+
AUDIO/
TV/VCR
CATV/DBS
Cursor and
ENTER
SURROUND
MODE
ENTER buttons
VOLUME
NORMAL
+0
GAMMA
+0
BRIGHTNESS
+0
CONTRAST
+0
SATURATION
+0
TINT
+3
SHARPNESS
Y DELAY +0
Normally, select this.
Suitable for a movie source.
affect the appearance of
picture and store the settings.
To adjust USER 1 or USER 2
1 Press VFP (PROGRESSIVE), then press Cursor 3/2
SUPER
repeatedly to select "USER 1" or "USER 2."
VCD
2 Press Cursor ∞/5repeatedly to select a
parameter you want to adjust.
• Adjust gradually to show preferable appearance by
confirming the picture.
• GAMMA:
Controls the brightness of neutral tints while maintaining
the brightness of dark and bright portions (–4 to +4).
• BRIGHTNESS:
Controls the brightness of the screen (–16 to +16).
• CONTRAST:
Controls the contrast of the screen (–16 to +16).
• SATURATION:
Controls the color depth of the screen (–16 to +16).
• TINT:
Controls the tint of the screen (–16 to +16).
• SHARPNESS:
Controls the sharpness of the screen (+0 to +3).
• Y DELAY:
Controls the color gap of the screen (–2 to +2).
3 Press ENTER.
VFP menu disappears, and the following pop-up window
appears on the TV.
GAMMA +0
4 Press Cursor 5/∞ repeatedly to change the
setting.
5 Press ENTER.
The current VFP settings appear again.
6 Repeat steps 2–5 to adjust other parameters.
To return to the normal screen
Press VFP (PROGRESSIVE).
To activate your setting
Press VFP (PROGRESSIVE), then press Cursor 3/2
repeatedly to select "USER 1" or "USER 2."
NOTE:
The VFP settings disappear if no operations are done for more than
about 10 seconds.
USER 1
+0
GAMMA
+0
BRIGHTNESS
+0
CONTRAST
+0
SATURATION
+0
TINT
+3
SHARPNESS
+0
Y DELAY
+ 0
GAMMA
48