Multi-Function Door Control (Optional) - LiftMaster ATS2113X 1/2 HP Manuel D'installation

Multi-Function Door Control (Optional)

INSTALLATION
Locate door control within sight of the door at a minimum
height of 5 feet (1.5 m) where small children cannot reach,
and away from moving parts of the door and door hardware.
If installing into drywall, drill 5/32" holes and use anchors
provided. For pre-wired installations (as in new home
construction), it may be mounted to a single gang box.
NOTE: After installation, a green indicator light behind the
cover will indicate proper connection. If not lit, the Lock and
Light features will not function (reverse wires to correct).
1. Strip 1/4" (6 mm) of insulation from one end of bell wire
and connect to the two screw terminals on back of door
control by color: white wire to 2 and white/red wire to 1.
2. Remove cover by gently pushing both thumbs against
upper corners of cover on back side of door control. Fasten
with 6ABx1-1/4" self-tapping screws (standard installation)
or 6-32x1" machine screws (into gang box) as follows:
• Drill and install bottom screw, allowing 1/8" (3 mm) to
protrude above wall surface.
• Position bottom of door control on screw head and slide
down to secure. Adjust screw for snug fi t.
• Install top screw with care to avoid cracking plastic
housing. DO NOT overtighten.
• Insert bottom tabs and snap on cover. (To remove cover
after mounting, gently pry at top with paper clip or small
fl at head screwdriver.)
3. (Standard installation only) Run bell wire up wall and
across ceiling to the operator. Use staples to secure wire in
several places. DO NOT pierce wire with a staple, creating a
short or open circuit.
4. Connect bell wire to the operator terminal screws: white to
2 and white/red to 1.
5. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location on
inside of door.
NOTE: DO NOT connect the power and operate the operator
at this time. The trolley will travel to the full open position but
will not return to the close position until the sensor beam is
connected and properly aligned. See safety reversing sensor
instructions beginning on page 15.
Multi-Function Door Control
Panel Terminal Screws
2-Conductor Bell Wire
Door Control
Push Bar
Lock
Button
Operator Terminal Screws
Back Panel of
Light
Button Operator
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is NOT connected BEFORE installing
door control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from
a closing door:
• Install door control within sight of door, out of reach
of children at a minimum height of 5 feet (1.5 m),
and away from ALL moving parts of door.
• NEVER permit children to operate or play with door
control push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to
door travel.
• ALWAYS keep door in sight until completely closed.
NEVER permit anyone to cross path of closing door.
OPERATION OF THE MULTI-FUNCTION DOOR CONTROL
Press the push button to open or close
the door. Press again to reverse the door
during the closing cycle or to stop the
door while it's opening.
Light feature
Press the Light button to turn the
operator light on or off. It will not control
the operator lights when the door is in motion. If you turn it
on and then activate the operator, the light will remain on for
4-1/2 minutes. Press again to turn it off sooner. The 4-1/2
minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button until the
light blinks (about 10 seconds).
A single blink indicates that the timer is reset to 1-1/2 minutes.
Repeat the procedure and the light will blink twice, resetting
the timer to 2-1/2 minutes. Repeat again for a 3-1/2 minute
interval, etc., up to a maximum of four blinks and 4-1/2
minutes.
Lock feature
Designed to prevent operation of the door from hand-held
remote controls. However, the door will open and close from
the Door Control and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds. The
push bar light will fl ash as long as the Lock feature is on.
To turn off, press and hold the Lock button
again for 2 seconds. The push bar light will
stop fl ashing. The Lock feature will also turn
off whenever the "LEARN" button on the
motor unit panel is activated.
Antenna
31
Lighted
Push
Button
Lock
Button
Light
Button