Sony XM-5ES Mode D'emploi page 6

INPUT MODE section:
 CH 1-4 switch
Selects the input mode for CH 1, CH 2, CH 3 and
CH 4.
• "1-4": For 4-channel stereo input.
INPUT 1
INPUT 2
INPUT 3
INPUT 4
• "1": For 1-channel input.
INPUT 1
• "1-2": For 2-channel input.
INPUT 1
INPUT 2
• "1+3/2+4": For 4-channel input.
INPUT 1
INPUT 3
INPUT 2
INPUT 4
 SUB CH switch
Selects the input mode for SUB CH (subwoofer
channel).
• "5": For mono subwoofer input.
INPUT 5
• "5+6": For stereo subwoofer input.
INPUT 5
INPUT 6
• "1+2": Uses signal input from INPUT 1+2.
INPUT 1
INPUT 2
• "3+4": Uses signal input from INPUT 3+4.
INPUT 3
INPUT 4
 LINE OUT MODE switch
Sets the mode of signal output to LINE OUT 1
and 2 connectors. Signal output from all LINE
OUT connectors are unfiltered and not affected
by any FILTER settings.
• "THRU": Stereo output (through mode)
INPUT 1
INPUT 2
• "STEREO": Stereo output (summing mode)
INPUT 1
INPUT 3
INPUT 2
INPUT 4
• "ALL": Mono output (summing mode)
INPUT 1
INPUT 2
INPUT 3
INPUT 4
6
GB
CH 1
CH 2
CH 3
CH 4
CH 1
CH 2
CH 3
CH 4
CH 1
CH 3
CH 2
CH 4
CH 1
CH 3
CH 2
CH 4
SUB CH
SUB CH
SUB CH
SUB CH
LINE OUT 1
LINE OUT 2
LINE OUT 1
LINE OUT 2
LINE OUT 1
LINE OUT 2
CH 1/2 and CH 3/4 section:
 FILTER switch
Sets the filter mode for CH 1/2 and CH 3/4.
• "OFF": Turns the filter off.
• "HP" (high-pass): Frequencies lower than HPF
control setting are filtered.
• "LP" (low-pass): Frequencies higher than LPF
control setting are filtered.
• "BP" (band-pass): The range of frequency for
the HPF control is automatically fixed at 50 Hz
– 500 Hz; the range of frequency for LPF
control is automatically fixed at 500 Hz – 5
kHz. Frequencies outside the range of HPF
and LPF settings are filtered.
 RANGE switch
Sets the range of frequency for HPF (high-pass
filter) and LPF (low-pass filter) control.
• "50-500": Range of frequency for subwoofer.
• "500-5k": Range of frequency for midrange
speaker or tweeter.
 HPF (high-pass filter) control
Depending on the RANGE setting, adjusts the
cutoff frequency in the range of 50 Hz – 500 Hz
or 500 Hz – 5 kHz.
 LPF (low-pass filter) control
Depending on the RANGE setting, adjusts the
cutoff frequency in the range of 50 Hz – 500 Hz
or 500 Hz – 5 kHz.
 INPUT SENS (input sensitivity) control
Adjusts the input level sensitivity for CH 1/2 and
CH 3/4.
Turn the knob clockwise when the output level
of the connected audio devices is low.
SUB CH section:
 SUBSONIC FILTER switch
Turns the subsonic filter on or off.
 SUBSONIC FILTER control
Adjusts the cutoff frequency (5 Hz – 50 Hz) of the
subsonic filter.
 LPF (low-pass filter) switch
Turns the low-pass filter on or off.
 LPF (low-pass filter) control
Adjusts the cutoff frequency (50 Hz – 500 Hz) of
the low-pass filter.
 INPUT SENS (input sensitivity) control
Adjusts the input level sensitivity for SUB CH.
Turn the knob clockwise when the output level
of the connected audio devices is low.
 SPEAKER OUT terminal screw head
 +12 V terminal screw head
REMOTE terminal screw head
GROUND terminal screw head