Installation Requirements; Location Requirements - Jennair INSTAI.L JBSFS42NM Instructions D'installation

TOOLS AND PARTS
IMPORTANT:
Installer: Leave Installation Instructions with the
homeowner.
Homeowner: Keep Installation Instructions for future
reference. Save these Installation Instructions for the
local electrical inspector's use.
TOOLS NEEDED:
Gather the required tools and parts before starting
installation. Read and follow the instructions provided
with any tools listed here.
Cordless drill
Drill bits
Adjustable wrenches (2)
Phillips screwdriver
Small level
3/8" and 1/2" open-end
wrenches
1/4" and 5/16" socket
drivers
Parts Needed:
#8 x 3" (7.6 cm) wood screws (longer screws may be
needed) (6)
2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)
(1 or 2)
Make custom panels or consult a qualified
cabinetmaker or carpenter to make the panels.
Overlay Series: Make custom panels, or consult a
qualified cabinetmaker or carpenter to make the
panels. See "Overlay Series Custom Panels and
Handle Kits" for more information.
Stainless is shipped complete.
If you are connecting the water line directly to copper
tubing and not to a shutoff valve, you need a ferrule, a
union, and a 1/4" (6.35 mm) compression fitting.

LOCATION REQUIREMENTS

WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from appliance.
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: This appliance is intended to be used in
household and similar applications such as:
†Torx and T27 are trademarks of Acument Intellectual Properties, LLC

INSTALLATION REQUIREMENTS

Torx T27 screwdriver
®†
11/32" nut driver
Appliance dolly
5/32" hex key
Utility knife
Tape measure
Staff kitchen areas in shops, offices and other working
environments.
Farm houses and by clients in hotels, motels and
other residential type environments.
Bed and breakfast type environments.
Catering and similar non-retail applications.
Observe all governing codes and ordinances.
It is recommended that you do not install near an
oven, radiator, or other heat source.
Do not install in a location where the temperature will
fall below 55°F (13°C).
Floor must support the refrigerator weight, more
than 600 lbs (272 kg), door panels and contents of
the refrigerator. Flooring under refrigerator must be
at same level as the room. Face of cabinetry must be
plumb.
Ceiling height must allow for side tipping radius. See
"Tipping Radius."
Location should permit door to open fully. See "Door
Swing Dimensions."
Location must permit top grille removal. See
"Opening Dimensions."
OPENING DIMENSIONS
To avoid tipping during use, the solid soffit must be
within 1" (2.5 cm) maximum above the refrigerator. If
the solid soffit is higher than 1" (2.5 cm) or one is not
available, then the refrigerator must be braced.
If anti-tip boards are needed, they must be installed
to the rear wall studs so that the bottom of the anti-
tip board is 84" (213 cm) from the floor. See "Install
Anti-Tip Boards" for more information.
IMPORTANT
NOTES:
A clearance of 1/2" (1.3 cm) must be maintained
above the top grille in order for the top grille to be
removed.
Do not remove the foam gasket from the top of
the compressor cover unless removal is necessary
to fit the unit under a soffit. Removal of the
gasket will cause loss in cooling efficiency.
If installing under a solid soffit, after, installation
raise the leveling legs so that the gasket is
pressed snugly against the soffit.
A
B
A. Gasket
B. Compressor cover
A grounded 3 prong electrical outlet should be
located within a specified number of inches from
the right-hand side cabinets or end panel. See the
chart following the graphic for the number of inches
required for your model. For more information, see
"Electrical Requirements."
1/2"
(1.3 cm)
5