Bosch GSB Professional 13 Notice Originale page 8

OBJ_BUCH-3415-002.book Page 8 Thursday, January 11, 2018 9:40 AM
8 | English
Impact Drill
Max. drilling dia.
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to EN 60745-2-1.
Typically the A-weighted noise levels of the product are: Sound pressure level 100 dB(A); Sound power level 111 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined
h
according to EN 60745-2-1:
Drilling in metal:
a
h
K
Impact drilling in concrete:
a
h
K
Screwdriving:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
 Before any work on the machine itself, pull the mains
plug.
1 609 92A 46P | (11.1.18)
GSB 13 GSB 13 RE
mm 13
mm 10
mm 20
mm 1.5 – 13 1.5 – 13
kg 1.6
/II
Auxiliary Handle (see figure A)
 Operate your machine only with the auxiliary handle 9.
The auxiliary handle 9 can be set to any position for a secure
and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 9 in anticlockwise
direction and insert the depth stop 11.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
Afterwards, tighten the bottom part of the auxiliary handle 9
again by turning in clockwise direction.
The knurled surface of the depth stop 11 must face upward.
Changing the Tool
Keyless Chuck (see figure B)
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction , until the tool can be in-
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
turn the front sleeve 2 in rotation direction  by hand until
the locking action is no longer heard. This automatically locks
the drill chuck.
The locking is released again to remove the tool when the
front sleeve 2 is turned in the opposite direction.
GSB 16 GSB 16 RE
13 16
10 12
20 25
1.5 – 13
1.6 1.8
/II /II
3 601 ... B27 0..
B27 1..
2
m/s 4.0
2
m/s 1.5
2
m/s 14.0
2
m/s 1.5
2
m/s 1.0
2
m/s 1.5
Bosch Power Tools
16
12
25
1.5 – 13
1.8
/II
B28 0..
B28 1..
7.5
1.5
13.0
1.5
<2.5
1.5