Denon DJ PRIME 2 Guide D'utilisation Rapide page 7

33. Censor / Reverse: Press this button to activate/deactivate the Censor feature: the playback of the track will be
reversed, but when you release the button, normal playback will resume from where it would have been if you
had never engaged the Censor feature (i.e., as if the track had been playing forward the whole time).
Press and hold Shift and then press this button to reverse the playback of the track normally.
34. Performance Pads: These pads have different functions on each deck depending on the current pad mode.
35. Hot Cue: Press this button to enter Hot Cue Mode. See the User Guide for more information.
36. Loop: Press this button once to enter Manual Loop Mode, and press it again to enter Auto Loop Mode. See the
User Guide for more information.
37. Roll: Press this button to enter Roll Mode. See the User Guide for more information.
38. Slicer: Press this button once to enter Slicer Mode, and press it again to enter Slicer Loop Mode. See the User
Guide for more information.
39. Parameter /: Use these buttons for various functions in each Pad Mode. See the User Guide for more
information.
40. Auto Loop / Loop Move: Turn this knob to set the size of an automatic loop. The value will be shown in the
touchscreen and platter display.
Press this knob to activate or deactivate an automatic loop at the current location of the track.
Press and hold Shift and turn this knob to shift the active loop to the left or right.
41. Loop In / Loop Out: Press either of these buttons to create a Loop In or Loop Out point at the current location. Their
placement will be affected by the Quantize and Smart Loops settings. See the User Guide for more information.
48
46 47
43
42. FX On: Press these buttons to enable or disable FX 1 and FX 2.
Press and hold Shift and press either of these buttons to show or hide the FX bar.
43. FX Select: Turn these knobs to select the active effect for FX 1 and FX 2.
44. FX Time/Parameter: Turn these knobs to decrease or increase the rate of time-based effects on that deck.
Press these knobs to toggle between FX Time and FX Parameter control, and then turn the knobs to adjust the
parameter.
45. FX Wet/Dry Knob: Turn this knob to adjust the wet/dry mix of the effects.
46. Mic On/Off: Press this button to activate/deactivate the microphones.
47. Mic Level: Turn these knobs to adjust the volume levels of the corresponding microphone inputs. The Peak light
next to each knob indicates the current signal level by its color: green (low), amber (normal/optimal), or red
(maximum/peak).
Important: The audio signals from the microphones are routed directly to the Master Outputs.
48. Mic EQ: Turn these knobs to boost or cut the high, mid-range and low frequencies for the microphones.
49. Talkover: Press this button to use the "talkover" feature, which automatically reduces the volume level of the
master mix when you speak into the microphone.
50. Master Level: Turn this knob to adjust the volume level of the Master Outputs.
51. Booth Level: Turn this knob to adjust the volume level of the Booth Outputs.
52. Aux Level: Turn this knob to adjust the volume level of the Aux Inputs.
53. Aux Cue: Press this button to send the aux signal to the headphones' cue channel.
54. SD Card Slot: Insert a standard SD card to this slot. When you select that SD card as a source, you can use the
display to select and load tracks from your SD card.
55. USB 1 Port: Connect a standard USB flash drive to this USB port. When you select that USB flash drive as a
source, you can use the display to select and load tracks from your USB flash drive.
Important: You must use the Engine Prime software to configure the music library on your SD Card or USB flash
drive before connecting them to PRIME 2. See the complete User Guide at
56. Eject/Source: Press this button to bring up on the touchscreen a list of connected media devices which can be
ejected. Tap one of the listed media sources to eject that device. To prevent data corruption, drives must be ejected
before being removed from the player. Press and hold Shift and press this button to open the Source menu.
48 48
49
42
44 45
52 53
50 51
42
43 44 45
denondj.com to learn how to do this.
54 55
56
7