Télécharger Imprimer la page

DeWalt DW130 Guide D'utilisation

Perceuse de 13 mm (1/2 po) à poignée-bêche
Masquer les pouces Voir aussi pour DW130:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

D
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
E
Printed in U.S.A. (JUL02-CD-1) Form No. 384162-02
The following are trademarks for one or more D
scheme; the "D" shaped air intake grill; the array of pyramids on the handgrip; the kit box con-
figuration; and the array of lozenge-shaped humps on the surface of the tool.
Important Safety Instructions
WARNING: When using electric tools, basic safety precautions should always be
followed to reduce risk of fire, electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
Safety Instructions For All Tools
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence
of flammable liquids or gases.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For
example; pipes, radiators, ranges, and refrigerator enclosures.
• KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors
should be kept away from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-
up place — out of reach of children.
• DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was intend-
ed.
• USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy-duty tool.
Don't use tool for purpose not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving
parts. Non-skid footwear is recommended when working outdoors. Wear protective hair cov-
ering to contain long hair.
Air vents often cover moving parts and should also be avoided.
• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.
• DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It's safer than using your hand and it
frees both hands to operate tool.
• DON'T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer perfor-
mance. Follow instructions for lubricating and changing accessories. Inspect tool cords peri-
odically and if damaged, have repaired by authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and
grease.
• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys
and adjusting wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch
is off when plugging in.
• EXTENSION CORDS. Use only 3-wire extension cords that have 3-prong grounding-type
plugs and 3-pole receptacles that accept the tool's plug. Replace or repair damaged cords.
Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. The following table
shows the correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Recommended Minimum Wire Size for Extension Cords
Total Length of Cord
25 ft.
50 ft.
75 ft.
100 ft.
7.6 m
15.2 m
22.9 m
30.5 m
Wire Size
18 AWG
18 AWG
16 AWG 16 AWG 14 AWG 14 AWG 12 AWG
DW130,DW130-220
Copyright © 2002
WALT power tools: the yellow and black color
E
125 ft.
150 ft.
175 ft.
38.1 m
45.7 m
53.3 m
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when
you are tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving parts, binding of moving parts, break-
age of parts, mounting, and any other conditions that may affect its operation. A guard or
other part that is damaged should be properly repaired or replaced by an authorized service
center unless otherwise indicated elsewhere in this instruction manual. Have defective
switches replaced by authorized service center. Do not use tool if switch does not turn it on
and off.
CAUTION: When drilling or driving into walls, floors or wherever live electrical wires may
be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only
by insulated grasping surfaces to prevent electric shock if you drill or drive into a live wire.
Additional Safety Instructions
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
CAUTION: Wear appropriate hearing protection during use. Under some conditions and
duration of use, noise from this product may contribute to hearing loss.
• The label on your tool may include the following symbols.
V ..........................volts
Hz ........................hertz
min ........................minutes
......................direct current
.......................... Class II Construction
..........................safety alert symbol
Double Insulation
Double insulated tools are constructed throughout with two separate layers of electrical insu-
lation or one double thickness of insulation between you and the tool's electrical system. Tools
built with this insulation system are not intended to be grounded. As a result, your tool is
equipped with a two prong plug which permits you to use extension cords without concern for
maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when operat-
ing this tool. The insulation system is for added protection against injury resulting from a pos-
sible electrical insulation failure within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair
or replace damaged cords.
Polarized Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk
of electric shock. When provided, this plug will fit in the polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
SAVE THESE INSTRUCTIONS
Motor
Your D
WALT tool is powered by a D
E
with the nameplate marking. The markings; 120, 220 volts, 50/60 Hz or "AC/DC", mean that
your drill will operate on alternating or direct current.Voltage decrease of more than 10% will
cause loss of power and overheating. All D
operate, check the power supply.
Spade Handle Assembly: (Fig. 1)
This spade handle can be attached either horizontally or vertically. Place the handle into the locating
boss on the back of the drill and assemble with holding knob.
Side Handle
(Fig. 1)
The side handle can be placed in either side of the drill or the top of the drill according to operator
preference and available working clearance. The spade handle can be temporarily removed if working
clearance at rear of tool is limited. Always replace spade handle when possible.
CAUTION: Always use the side handle and switch handle. This is a high-torque drill. Always hold it
firmly with both hands when operating.
Switch:
(Fig. 2)
Pressing the TOP part of the switch runs the tool in a reverse direction (A). Pressing the BOT-
TOM part of the switch runs the tool in a forward direction (B). Always let the motor stop com-
pletely before changing direction.
To lock trigger in "FORWARD" position, depress LOWER part of trigger and push up lock but-
ton (C). Then, while holding lock button in position, gently release trigger. To release locking
mechanism, depress trigger fully, then release it.
NOTE: Locking mechanism will not function if upper part of trigger is depressed (reverse oper-
ation).
The locking feature is for use when the drill is mounted in a drill stand or otherwise firmly
held...NOT BY HAND.
Do not lock the switch "ON" when drilling by hand so that you can instantly release the trigger
switch if the bit binds in the hole.
Be sure to release the switch locking button before disconnecting the plug from the power
supply. Failure to do so will cause the tool to start immediately the next time it is plugged in.
Damage or injury could result.operate, check the power supply.
Chuck
To insert bit, open chuck jaws by turning collar with fingers and insert shank of bit about 3/4"
(19mm) into chuck. Tighten chuck collar by hand. Place chuck key in each of the three holes
and tighten in clockwise direction. It's important to tighten chuck with all three holes. To
release bit, turn chuck key counterclockwise in just one hole, then loosen the chuck by hand.
Chuck Removal
(Figures 3 & 4)
1. Place chuck key in chuck as shown in Figure 3. Using a wooden mallet or similar object,
strike key sharply in a CLOCKWISE direction. This will loosen screw inside chuck.
2. Open chuck jaws fully. Insert screwdriver into front of chuck between jaws to engage screw
head. Remove screw by turning clockwise (left-hand thread).
3. Place key in chuck as shown in Figure 4. Using a wooden mallet or similar object, strike
key sharply in a COUNTERCLOCKWISE direction. This will loosen chuck so that it can be
unscrewed by hand.
A..........................amperes
W ........................watts
......................alternating current
n o ........................no load speed
........................earthing terminal
.../min ..................revolutions
per minute
WALT built motor. Be sure your power supply agrees
E
WALT tools are factory tested; if this tool does no
E

Publicité

loading

Sommaire des Matières pour DeWalt DW130

  • Page 1 Polarized Plugs WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 Printed in U.S.A. (JUL02-CD-1) Form No. 384162-02 DW130,DW130-220 Copyright © 2002 Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk of electric shock.
  • Page 2 FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are miss- bit through the last fractional part of the hole. ing, call 1-800-4-DEWALT for a free replacement. 8.Keep the motor running when pulling the bit back out of a drilled hole. This will help pre- vent jamming.
  • Page 3 sés. Perçage • L’étiquette de l’outil peut comporter les symboles suivants. Toujours débrancher l’outil lorsqu’on en change les forets ou les accessoires. V ....volts A ....ampères 2. N’utiliser que des forets bien affûtés. Pour le BOIS : forets hélicoïdaux, à langue d’aspic, Hz ....hertz W ..watts de tarière ou des emporte-pièce;...
  • Page 4 • VERIFIQUE LAS PARTES DAÑADAS. Antes de seguir empleando cualquier herramienta, Cualquier centro de servicio autorizado DeWALT puede instalarle a su taladro un portabrocas es indispensable verificar con mucho cuidado que las guardas u otras partes dañadas sin llave en lugar del que tiene.
  • Page 5 Si el portabrocas es demasiado grande para permitir quitar los dos tornillos de la parte supe- rior, vea las instrucciones de remoción del portabrocas. Carbones del motor Epecificaciones DW130 DW130-220 APAGUE Y DESCONECTE EL TALADRO DE LA TOMA DE CORRIENTE. Tensión de alimentación...

Ce manuel est également adapté pour:

Dw130-220