Milwaukee HEAVY DUTY M18 BP Notice Originale page 16

TECHNICAL DATA
Planer
Production code
No-load speed
Planing width
Planing depth
Rabbet depth
Battery voltage
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 12,0 Ah)
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841
Vibration emission value a
h
Uncertainty K=
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for di erent
applications, with di erent accessories or poorly maintained, the vibration and noise emission may di er. This may signi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched o or when
it is running but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and speci cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
PLANER SAFETY WARNINGS
a) Wait for the cutter to stop before setting the tool down.
An exposed rotating cutter may engage the surface leading to pos-
sible loss of control and serious injury.
b) Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by your hand or against the body leaves it unstable and may
lead to loss of control.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Always use the protective shields on the machine.
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is recom-
mended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Chips and splinters must not be removed while the machine is
running.
Do not drill the housing, as the protective insulation would be
rendered ine ective. Use adhesive labels.
Only plane with sharp blades and avoid metal (nails, screws).
Remove the battery pack before starting any work on the
appliance.
WARNING! To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in uid or allow a uid to ow inside them.
M18 BP
4526 26 06...
... 000001-999999
14000 min
-1
82 mm
2,0 mm
10,7 mm
18 V
3,2 kg - 4,3 kg
-18°C ... +50°C
M18B..., M18HB...
M12-18..., M1418...
82,8 dB (A)
93,8 dB (A)
4,3 m/s
2
1,5 m/s
2
English
13
GB GB