L.B. White Guardian 2.0 AD/AW100 Serie Manuel Du Propriétaire page 7

Attention - Critical
Points to Remember!
■ Propane gas and natural gas have a distinctive
odor. Learn to recognize these odors. (Reference
"Fuel Gas Odor" and "Odor Fading" sections.
■ If you have not been properly trained in repair and
service of propane gas and natural gas fueled
heaters, then do not attempt to light the heater,
perform service or repairs, or make any adjust-
ments to the heater on a propane gas or natural
gas fuel system.
■ Even if you are not properly trained in the service
and repair of gas-fired force air heaters, ALWAYS
be consciously aware of the odors of propane gas
and natural gas.
■ A periodic "sniff test" around the heater or at the
heater's joints; i.e. hose, connections, etc., is a
good safety practice under any conditions. Even if
you smell a small amount of gas, CONTACT YOUR
FUEL GAS SUPPLIER IMMEDIATELY. DO NOT
WAIT!
1. Do not attempt to install, repair, or service this
heater or the gas supply line unless you have
continuing expert training and knowledge of gas
heaters.
QUALIFICATIONS FOR SERVICING AND
INSTALLATION:
a. To be considered a qualified gas heater service
personnel, you must have been trained in gas-fired
heater servicing, repair and also have sufficient
experience to allow you to troubleshoot, replace
defective parts, and test heaters in order to get
them into a continuing safe and normal operation
condition. You must completely familiarize yourself
with each model heater by reading and complying
with the safety instructions, labels, owner's manual,
etc. that are provided with each heater.
b. To be a qualified gas installation person, you must
have sufficient training and experience to handle
all aspects of installing, repairing, and altering
gas lines, including selecting and installing the
proper equipment, and selecting proper pipe size
to be used. This must be done in accordance with
all local, state and national codes as well as the
manufacturer's requirements.
Guardian 2.0 LP or Natural Gas Heater
2. All installations or applications of L. B. White Co.,
LLC's heaters shall meet the requirements of
local, state and national L.P. gas and natural gas,
electrical and safety codes. Your gas supplier,
local licensed electrician, local fire department
and government agencies can help you determine
these requirements. In the absence of local codes,
comply with the following:
a. Installations in the U.S.A.:
-- ANSI/NFPA 58, latest edition, Standard for Storage
and Handling of Liquefied Petroleum Gas and/or
-- ANSI Z223.1/NFPA 54, National Fuel Gas Code
-- ANSI/NFPA 70, National Electrical Code.
b. Installations in Canada:
-- CAN1-B149.1 or CAN1-B149.2 Installation Codes
-- CSA C22.1 Part 1 Standard Canadian Electrical
Code. CSA C22.2 No.3, Electrical Features of Fuel
Burning Equipment.
3. Do not move, handle, or service the heater while in
operation or connected to a power or fuel supply.
4. This heater may be installed in areas subject to
wash down. This heater may only be washed
on the external case assembly—see Cleaning
Instructions. Do not wash the interior of the heater.
Use only compressed air, soft brush or dry cloth to
clean the interior of the heater and it's components.
After external wash down, do not operate this
heater until it is completely dry. In any event, do
not operate the heater for at least one hour after
external wash down.
5. For safety, this heater is equipped with a manual
reset high-limit switch and an air proving switch.
Never operate this heater with any safety device
that has been bypassed. Do not operate this heater
unless these features are fully functioning.
6. Do not operate the heater with its door open or
panel removed.
7. Do not locate fuel gas containers or fuel supply
hoses within 20 ft. of the blower outlet of the
heater.
8. Do not block air intakes or discharge outlets of the
heater. Doing so may cause improper combus-
tion or damage to heater components leading to
property damage or animal loss.
Owner's Manual • Guardian 2.0
7