Bosch EasyHammer 12V Notice Originale page 13

tery pack may create a risk of fire when used with another
battery pack.
Use power tools only with specifically designated bat-
u
tery packs. Use of any other battery packs may create a
risk of injury and fire.
When battery pack is not in use, keep it away from
u
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
Under abusive conditions, liquid may be ejected from
u
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addi-
tionally seek medical help. Liquid ejected from the bat-
tery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or
u
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
Do not expose a battery pack or tool to fire or excess-
u
ive temperature. Exposure to fire or temperature above
130°C may cause explosion.
Follow all charging instructions and do not charge the
u
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of bat-
u
tery packs should only be performed by the manufacturer
or authorized service providers.
Hammer and Drill Safety Warnings
Safety instructions for all operations
Wear ear protectors. Exposure to noise can cause hear-
u
ing loss.
Brace the tool properly before use. This tool produces a
u
high output torque and without properly bracing the tool
during operation, loss of control may occur resulting in
personal injury.
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory or fasteners may contact hidden wiring. Cut-
ting accessory or fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum
u
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Bosch Power Tools
Always start drilling at low speed and with the bit tip
u
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety information
Use auxiliary handle(s), if supplied with the tool. Loss
u
of control can cause personal injury.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Protect the power tool against heat, e.g.
against continuous intense sunlight, fire,
water, and moisture. There is a risk of explo-
sion.
Product Description and
Specifications
fire and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for hammer drilling in concrete,
brick and stone. It is also suitable for drilling without impact
in wood, metal, ceramic and plastic. Power tools with elec-
tronic control and right/left rotation are also suitable for
screwdriving.
English | 13
Read all the safety and
general instructions. Fail-
ure to observe the safety
and general instructions
may result in electric shock,
1 609 92A 4MK | (28.01.2021)