IMER SPIN 15 Manuel D'utilisation Et Entretien page 12

Dear Customer,
compliments on your purchase: this IMER mixer, the result of
and innovative technical solutions.
- WORKING IN SAFETY.
To ensure complete safety, read all the instructions in this
manual carefully.
This OPERATION AND MAINTENANCE manual must be kept
by the Site Manager and be always available for consultation.
The manual is considered part of the machine and must be stored
for future reference ( EN ISO 12100 ) through to scrapping of the
machine itself. If the manual is lost or damaged, a replacement
copy can be ordered from the manufacturer.
The manual contains the EC declaration of conformity (2006/42/
EC) important information on construction site procedures, in-
stallation, operation, maintenance and requests for spare parts.
Nevertheless, the user must both have adequate experience
and knowledge of the machine prior to use: the user should be
trained by a person totally familiar with the operation and use of
this machine.
To guarantee complete safety of the operator, safe operation
and long life of equipment, follow the instructions in this manual
carefully, and observe all safety standards currently in force for
the prevention of accidents at work (use of safety footwear and
suitable clothing, helmets, gloves, goggles etc.).
- Make sure that all signs are legible.
- It is strictly forbidden to carry out any form of modi-
IMER INTERNATIONAL accepts no responsibility in the event of
damage or defects on machinery or equipment not supplied by
IMER and used in combination with IMER machinery.
IMER INTERNATIONAL accepts no responsibility in the event
of failure to comply with laws governing the use of this type of
equipment, with particular reference to: improper use, incorrect
failure to comply, either wholly or partially, with the instructions
set out in this manual.
IMER INTERNATIONAL reserves the right to modify the cha-
racteristics of the mixer and/or contents of this manual, without
the obligation to update the previous machine and/or manuals.
1. TECHNICAL DATA
2. DESIGN STANDARDS
The continuous mixers have been designed and constructed
3. NOISE EMISSION LEVEL
Table 1 shows the sound pressure levels of the mixer measured
at the ear of the operator (L at 1 m) and noise emission levels
pA
in the environment (power L ) measured according to EN ISO
WA
3744 (2000/14/CE)
IMER INTERNATIONAL S.p.A.
SPIN 15
4. DESCRIPTION OF MIXER OPERATION
for use in building sites, for mixing and pumping all mixed
mortars declared as compatible with this type of machine by
the material manufacturers: brickwork plasters, mortars for
semi-dry tiles, cement mixes, lime/cement based plasters,
grouting mortar etc
The mixer comprises a wheeled frame (ref.1), which supports a
hopper (ref.2), a mixing chamber (ref.3), a water circuit (ref.9), an
electrical panel (ref.5).
There is a version of horizontal mixer with the water pump already
assembled (ref. 11).
The pre-mixed dry material is poured in to the hopper (using sacks
or by means of other equipment), which houses an auger batching
system (ref.6), activated by a gearmotor (rif.7), which moves the
auger, transferring the material into the mixing chamber. This
mixes the material with water delivered directly to the chamber by
the water pump and via the water circuit.
The mixed material is then conveyed to the discharge outlet (ref.4),
ready to use and collected in crates, wheelbarrows, buckets etc.
and then applied manually where required.
5. OPERATION SAFETY
safety devices.
or discharge outlet during operation.
ronments.
All current standards governing accident prevention and safety
devices must be observed in the workplace.
Take care when handling sacks of material to avoid dispersion of
dust with inhalation of the latter; if this is not possible, masks must
be worn to protect the mouth and nose.
The mixer is not equipped with a lighting system and therefore the
The power lines must be laid to prevent any possible damage.
Never place the mixer on electric power cables.
Ensure that the electrical connection is protected against the risk
of water penetration in connectors. Use exclusively connectors
and couplings equipped with water spray protection.
- Never use inadequate or provisional electric lines: if in doubt
consult specialist personnel for assistance.
- Repairs to the electrical circuit must be performed exclusively by
specialised personnel. Disconnect the machine from the power
supply before performing maintenance or repairs.
-Avoid contact of electric wires with movable and/or moving parts
of the machine. to avoid injury from contact with live metal parts.
-CAUTION!
6. ELECTRIC SAFETY
The SPIN15 mixer is constructed according to standard EN 60204-1,
with protection against water sprays and protection against overload
and power failure.
The mixer must be connected to the earthing circuit.
To facilitate transport, the machine can be disassembled as
12
- THE CONTINUOUS HORIZONTAL MIXER is designed
-
- Never insert parts of the body and/or tools in the hopper
-
- Never use the machine in areas subject to the risk of
Keep the hands away from the outlet.
-