Maintenance And Service - Bosch GBL 18V-120 Notice Originale

OBJ_BUCH-2544-002.book Page 7 Monday, June 20, 2016 9:42 AM
Cordless blower
Permitted ambient temperature
– during charging
2)
– during operation and during
storage
Recommended batteries
Recommended chargers
Recommended chargers for
wireless charging batteries
Operating duration per battery-
pack charge
– Blower level I
– Blower level II
Technical data determined with battery from delivery scope.
1) depending on the battery pack being used
2) Limited performance at temperatures <0 °C
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The battery must be removed from the power tool to charge it.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The "Electronic Cell Protection (ECP)" protects the lithium-
ion battery against deep discharging. When the battery is dis-
charged, the power tool is switched off by a protective circuit.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.
Removing the battery (see figures A1 – A2)
The battery 3 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 7 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery 3, press the unlocking buttons 7 and
pull the battery out of the machine to the rear. Do not ex-
ert any force.
Bosch Power Tools
Mounting the Blower Accessories
GBL 18V-120
(see figures B1 – B3)
 Remove the battery before cleaning or performing
°C 0...+45
maintenance on the blower, making tool adjustments,
°C –20...+50 changing accessories or storing the blower. This safety
measure prevents the blower from being started acciden-
GBA 18V..
tally.
GBA 18V... W
See the illustration for the ways of combining the different
AL 18..
blower accessories.
GAL 3680
– Insert the bayonet lock 12 of the accessory firmly into the
notches 8 of the motor housing or into the notches 8 of the
GAL 18... W
extension tube 9.
– Turn the bayonet lock a quarter turn clockwise.
min/Ah 9
Mounting the Dust Collection Tube
min/Ah 5
When blowing out bore holes, the drilling debris is blown in
the direction of the operator. For this reason, it is recom-
mended that you mount the dust collection tube 11 over the
bore hole nozzle 10.
– Place the notches 13 of the dust collection tube 11 over
the outer bayonet lock 12 of the bore hole nozzle 10.
– Turn the dust collection tube 11 a quarter turn clockwise.
Operation
 Remove the battery before cleaning or performing
maintenance on the blower, making tool adjustments,
changing accessories or storing the blower. This safety
measure prevents the blower from being started acciden-
tally.
Starting Operation
Switching On and Off
To save energy, only switch the power tool on when using it.
– To switch on the power tool, press the On/Off switch 1 to
position I or II.
Position I: Blowing together light materials.
Position II: Blowing together heavy materials.
– To switch off, push the On/Off switch 1 to the stop in po-
sition "0".
Working Advice
Never blow dirt in the direction of bystanders.
Always hold the power tool approx. 3 cm above ground when
working.
Do not blow hot, flammable or explosive material.
During "blowing" operation, take care that no debris/impuri-
ties can be drawn into the air intake 4.

Maintenance and Service

Maintenance and Cleaning
 Remove the battery before cleaning or performing
maintenance on the blower, making tool adjustments,
changing accessories or storing the blower. This safety
measure prevents the blower from being started acciden-
tally.
English | 7
1 609 92A 39U | (20.6.16)