Publicité
Les langues disponibles
Les langues disponibles
power tool designation
The power tool is designed for polishing surfaces with
liquid polishing compounds�
The area of the tool application can be expanded due
to use of additional accessories�
Power tool
components
1
Rubber plate *
2 Reducer
3 Spindle lock
4 Ventilation slots
5 Auxiliary handle *
6 Speed selector thumbwheel
7 Lock-off button
8 On / off switch
9 Wrench *
10 Polishing bonnet *
11 Rubber plate (sticky) *
12 Spindle
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation
of power tool elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / replacement of accessories
After mounting accessories of any kind,
make a trial run before commencing op-
eration - start the power tool and let it
work in idle mode for not less than 30
seconds. The operation of accessories with radial
or axial run-out and causing increased vibration of
the power tool is strictly forbidden.
Mounting of rubber plate (see fig. 1, 2)
• Press and hold spindle lock 3�
• Screw rubber plate 1 on spindle 12 and tighten it by
wrench 9 (see fig. 1).
• Put polishing bonnet 10 on rubber plate 1 (see fig. 2).
Mounting of rubber plate sticky (see fig. 3, 4)
• Press and hold spindle lock 3�
• Screw rubber plate 11 on spindle 12 and tighten it
manually (see fig. 3).
• Press polishing accessory to rubber plate 11 (see
fig. 4).
Initial operating
of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
DWT
Switching the power
Switching on:
In order to switch on the power tool, push lock-off but-
ton 7 and while holding it in position, push switch but-
ton 8�
Switching off:
In order to switch off the power tool, release switch
button 8�
Rotation stabilizer
Rotation stabilizer (on-load stabilization of rotation)
maintains set rotation rate irrespective of press force
on the surface being polished - the uniform rotation
rate of the wheel ensures the best quality of polishing�
Speed selector thumbwheel
Using revolution adjustment switch 6, you may select
the required spindle speed (also during operation)�
The required speed is dependent on the material and
can be determined with practical trials�
When operating your power tool at a low speed for a
long time, it has to be cooled down for 3 minutes� To
do it, set a maximum speed and leave your power tool
to run idle�
on the power tool operation
•
It is strongly recommended to use liquid polishing
compounds� Never use abrasive or grinding com-
pounds� Abrasive components may damage coated
surfaces�
• Run the power tool idle for one minute before the
operation�
• Regularly apply the polishing compound on the sur-
face during polishing�
• When applying the polishing compound on the pol-
ishing accessory leave approximately one forth of the
working surface uncovered by the compound�
• The quality of polishing depends on proper selection
of the rotation speed, which is mainly determined by
the material being processed�
• High speed is set when high quality of polishing is
not required�
• Use low speed to deliver the best quality of polishing
and to achieve high finish of the surface.
• If the part being processed is heated up, stop opera-
tion and let it cool down to avoid deformation�
Power tool maintenance /
preventive measures
Before carrying out any works on the power tool it
must be disconnected from the mains.
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� Regularly
English
16
tool on / off
Design features
of the power tool
Recommendations
Publicité
