Publicité
Never draw in fluids contain-
ing solvents or undiluted ac-
ids and solvents! This in-
cludes petrol, paint thinner
and heating oil. The spray
mist is highly inflammable,
explosive and poisonous. Do
not use acetone, undiluted
acids and solvents, as they
corrode the materials used on
the appliance.
Description of the Appliance
When unpacking the product, make sure that no acces-
sories are missing and that none of the package con-
tents have been damaged. If you detect any transport
damages please contact your dealer.
Illustration
1
Casing
2
Handle
3
Twist grip Power (for adjustment of the cleaning
pressure)
4
Foot pedal for edge cleaning
5
Foot pedal for surface cleaning
6
Bayonet connection with union nut
7
Extension tube
8
Extension tube detergent
9
Dosage regulator for detergent
10 Retainer Plug 'n' Clean detergent bottle
11 Rotor arm
12 Green high-pressure nozzle
13 Yellow high pressure nozzles (2 pieces)
14 Grey high-pressure nozzles (2 pieces)
15 Safety clip
16 Protective grid
Preparing the Appliance
Selecting the high pressure nozzles
You need to use the matching high pressure nozzles to
ensure that your high pressure cleaner works properly.
Note
Nominal pressure (p): See operating instructions or type
plate of your pressure washer.
High-pressure cleaner with nominal pressure (p) of
13 MPa (130 bar) to 16 MPa (160 bar)
e.g.: K 6 – K 7, Kärcher 600 – Kärcher 770
Use yellow high-pressure nozzles.
Note
The yellow high-pressure nozzles have already been in-
stalled.
High-pressure cleaner with nominal voltage (p)
lesser than 13 MPa (130 bar)
e.g.: K 4 – K 5, Kärcher 201 – Kärcher 560
Use grey high-pressure nozzles.
Changing the high pressure nozzles
Illustration
1
Loosen the safety clamp with a screwdriver.
2
Remove the protective grid.
3
Remove the clip.
4
Pull out the yellow high-pressure nozzle.
5
Insert the grey high-pressure nozzle.
6
Reinsert the clip.
7
Mount the protective grid on the pin.
8
Push the safety clamp in until it locks.
Note
Always use Kärcher water filter (order no. 4.730-059.0)
during suction operations of the high-pressure cleaner.
Cleaning floor surfaces
Apply detergent solution
Fasten the T-Racer with the extension tube detergent
and the extension tube to the high-pressure gun.
Illustration
1
Press the extension tube detergent onto the bayo-
net connection of the T-Racer.
2
Turn it by 90° until it locks into place.
3
Tighten the union nut.
Repeat this process even for the other joints.
Insert the detergent supply hose into the T-Racer.
Illustration
Adjust the twist grip "Power" in accordance with the
surface to be cleaned.
Remove the lid from the Plug 'n' Clean detergent
bottle and press the detergent bottle into the deter-
gent connection with the opening facing down.
Adjust the suction volume of the detergent solution
by means of the dosage regulator for detergents.
Unlock the lever on the trigger gun.
Pull on the lever of the trigger gun; the device will
switch on.
Cleaning floor surfaces
Set the dosing regulator for detergent to minimum and
clean the floor area again.
Tips for cleaning
Outdoor surfaces should be swept before the T-
Racer is used to avoid damaging the high-pressure
nozzles.
Prior to use on sensitive surfaces (e.g. wooden sur-
faces), test the product on an imperceptible spot, in
order to promptly detect any changes in the sur-
face.
The T-Racer is not suited for scouring or scrubbing!
Guide the T-Racer over the surface without effort.
Do not remain at one spot; always keep moving
during cleaning.
CAUTION
Do not run over protruding corners!
Illustration
– 2
EN
Application
11
Publicité
