Zibro SRE346E Manuel D'utilisation page 41

e - 2 Starting problems.
e - 5 Tipping-over protection.
e - 6 Poor burning.
e - 7 Room temperature
above 32°C.
e - 8 Defective booster.
e - 9 Air filter dirty; or
Fuel pump dirty.
The heater has been in operation
continuously for a period of 50 hours
and has turned itself off automatically.
Out of fuel.
-- : -- +
-- : -- Too little ventilation.
+
e - 1 1
Too little ventilation.
+
Always contact your Zibro dealer for any malfunctioning not listed above.
AUTOMATIC DEACTIVATION
This heater is fitted with a safety system that ensures that it switches off
automatically after 50 hours continuous operation. The following will then appear
in the display:
the button M (see Section D).
AUTOMATIC CLEANING MODE
When the heater has been burning continuously for two hours at its highest
setting, the burner will automatically start an autoclean procedure. The display
will show the autocleaning code cl:05 running back to cl:01. The procedure takes 5
minutes, during which the heater will burn at its lowest setting, while the burner
autocleans. When the burner is clean again, the heater will automatically switch
back to the highest setting again.
THE USE OF THE MOTION DETECTION SENSOR
This heater is equipped with a motion detection sensor. The sensor is placed at
the front side of the heater and it signals every single movement. The motion
detection sensor has a horizontal detection angle of 80
angle of 20 . The sensor detects movements as far as 7 m.
o
If the sensor does not detect movements for 10 minutes then the heater will
automatically switch to a lower combustion level. As a result less fuel will be used.
Switch on the motion detection sensor;
Switching on the motion detection sensor can only be done when the heater is
turned on. Push the "Motion" button
light will light up (green).
If the sensor does not detect movements for 10 minutes then the heater will
automatically switch to a lower combustion level. The motion detection sensor
light keeps lighted up. If the sensor detects movement the motion light will blink.
The heater switches back to the latest temperature setting.
Switch off the motion detection sensor;
The Motion detection sensor can be switched off by pressing the "Motion" button
again. A sound signal will be heard and the "Motion" light will go out.
4
80
p074_087_uk_SRE346E.indd 80-81
Contact your dealer.
Re-ignite the heater.
Contact your dealer.
If necessary,
re-ignite the heater.
Contact your dealer.
Clean filter
Contact your dealer.
Switch the heater back on.
Refill removable tank.
Ventilate better.
Ventilate better.
. If desired, you can switch the heater on again by pressing
and a vertical detection
o
. A signal will sound and the "Motion"
H
CHILDPROOF LOCK
The childproof lock can be used to prevent children accidentally changing the
heater settings. When the heater is burning and the childproof lock is on, the heater
can only be switched off. Other functions are blocked then. If the heater has already
been switched off, the childproof lock also prevents accidental ignition of the
ON
heater. Activate the childproof lock by pressing the appropriate key N and holding
OFF
it down for more than 3 seconds. The KEY-LOCK indicator (
SUN MON TUE WED THU FRI SAT
information display (Fig. H), indicating that the childproof lock has been activated.
day
H: When the mark
Switch off the childproof lock by pressing the key N and holding it down for more
appears, the childproof
than 3 seconds once again.
lock has been activated.
I
THE CORRECT USE OF 'SAVE'
The 'SAVE' function allows you to limit the temperature. When this function is
activated, the heater will automatically switch off, when the room temperature
exceeds the set temperature by 3°C. Subsequently, when the room temperature has
dropped again to the set temperature, the heater will automatically switch on again.
I: When the SAVE
Activate the 'SAVE' setting by pressing the appropriate Q key.
function is activated, the
heater will automatically
information display (Fig. I). Switch off the function by pressing the SAVE key once again.
switch on or off in
order to remain within
Without the 'SAVE' setting your heater will maintain the set temperature by
a specified temperature
range.
approximation as well, by adjusting its heating capacity. 'SAVE' is an economy
setting, which you can use when, for instance, you are not present in the room
or to keep it frost-free.
J
THE 'FUEL' INDICATOR
When the FUEL indicator appears, it means that there is only fuel left for 10
more minutes. The count-down of the remaining heating time can be seen in the
information display L (Fig. J). Now you have two options:
e
you remove the fuel tank and refill it outside the living room (section B) or
J: When the FUEL
e
you push the button extension S. By pushing this button, the remaining
indicator has appeard,
heating time will extend to 60 minutes.
the information display
The heater will automatically switch back to its lowest position. In the display
will show the number of
minutes of fuel left in the number 60 will appear, which will decline to 10. At the arrival of 10,
the tank.
you will hear an alarm signal every two minutes, warning you to refill the
removable tank. If you do not react, the heater will extinguish by itself. The
heater will also sound a warning signal, when it switches off. The fuel
indicator will blink, while four lines (--:--) are blinking in the information
display. You can stop this by pressing the
Once the heater has used up all its fuel and extinguished, it will take some time,
after the refill, before the heater is completely ready for use again.
K
THE 'VENT' INDICATOR
When there is insufficient ventilation in the room, an intermittent buzzer will
be heard (approximately once each 30 seconds) and the VENT indicator
be blinking. When this signal is given, ensure that the ventilation of the room is
K: A blinking
improved (e.g. by opening a door or window a little more), to avoid that the heater
indicator light is a sign
that you need extra
shuts off. When the ventilation of the room is improved, the VENT indicator and
ventilation.
buzzer will be deactivated. When there is still insufficient ventilation, the heater
) will appear on the
will display on the
button M once more.
will
4
81
16-05-11 10:39