DeWalt D27300 Traduction De La Notice D'instructions Originale page 29

8. Lower the guard (13) untill it contacts the chip collector and lock it
using the lever (12).
NOTE: If using a dust extractor, lower the upper table all the way and
attach the adapter to the dust chute, then raise the upper table until is
in contact with the adapter.
Adjustment
WARNING: Prior to adjustment always unplug the tool.
ADJUSTING THE FENCE (FIG. I1–I3)
Adjusting the Right Angle (fig. I1)
The fence has an adjustable stop for easy right angle adjustment.
1. Loosen the angle clamp handle (40).
2. Press the fence straight up to ensure it is fully vertical and tighten
the angle clamp handle.
3. Place a set square (41) on the table and up against the
fence (8).
4. If adjustment is required, proceed as follows:
5. Loosen the nut (42) a few turns and turn the vertical position
adjustment stop screw (43) in or out until the fence is at 90° to the
table as measured with the square.
Adjusting the Chamfering Angle (fig. I2)
1. Loosen the angle clamp handle (40).
2 Move the fence (8) along its longitudinal axle to achieve the required
angle.
3. Make sure that the lower edge of the fence touches the upper
table top (9).
4. Tighten the angle clamp handle.
Adjusting the Planing Width (fig. I3)
1. Loosen the fence clamp handle (7).
2. Move the fence (8) accross the upper table (9) to achieve the
required width.
3. Tighten the fence clamp handle.
ADJUSTING THE GUARD (FIG. J)
The guard can be adjusted to any fixed position above the table to
provide optimum screening.
WARNING: Always make sure to adjust the guard to the
planing width and the height of the workpiece.
To Adjust the Width
1. Loosen the lock knob (44).
2. Move the guard (13) to the required width.
3. Tighten the adjustment knob.
To Adjust the Height
1. Loosen the clamp handle (12).
2. Move the guard bracket (45) to the required height.
3. Tighten the clamp handle.
ADJUSTING THE DEPTH OF CUT (FIG. K, L1–L3)
Planing Mode (fig. K)
1. Loosen the locking ring (46).
2. Take hold of the depth adjustment knob (10) and adjust the depth
of cut using the scale (47).
– Turn clockwise to decrease the cutting depth.
– Turn counterclockwise to increase the cutting depth.
3. Tighten the locking ring.
Thicknessing Mode (fig. L1–L3)
1. Place the elevating handle (2) on to the elevating shaft end (48)
(fig. L1).
2. Rotate the handle (clockwise) until it makes contact with the shaft
nut.
3. Turn the elevating handle counterclockwise until it matches the hole
and flat side of the shaft.
4. Using a 2.5 mm hex key, tighten the dowel of the elevating handle
(fig. L2).
– Turn clockwise to decrease the cutting depth.
– Turn counterclockwise to increase the cutting depth.
5. Read the finished thickness of your workpiece on the depth
adjustment scale (5) (fig. L3).
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect machine from
power source before making any adjustments or
removing/installing attachments or accessories.
Ensure the machine is placed to satisfy your ergonomic conditions in
terms of table height and stability. The machine site shall be chosen so
that the operator has a good overview and enough free surrounding
space around the machine that allows handling of the workpiece
without any restrictions.
Prior to Operation
• Remove all foreign objects. Do not plane wood with loose knots.
Do not plane wood that is severely knotted or warped.
Switching On and Off (fi g. M)
The on/off switch offers multiple advantages:
NO-VOLT RELEASE FUNCTION
Should the power be shut off for some reason, the switch has to be
deliberately reactivated.
MOTOR OVERLOAD PROTECTION DEVICE
In case of motor overload, the power supply to the motor will be cut off.
If this happens, let the motor to cool for 2 minutes and then press the
green start button.
EXTRA SAFETY
The hinged safety enclosure plate can be locked by passing a padlock
through the hasp. The plate also serves as an "easy to locate"
emergency stop button as pressure on the front of the plate will depress
the stop button.
1. To switch the machine on, press the green start button (53).
2. To switch the machine off, press the red stop button (54).
WARNING: Always switch off the machine when work is
finished and before unplugging.
Planing (fi g. N1, N2)
1. Mount the guard/chip collector as described above.
2. Adjust the fence as required.
3. Adjust the guard to provide optimum screening.
4. Set the depth of cut.
5. Switch on the machine.
• Slowly feed the workpiece underneath the guard, keeping it firmly
pressed against the fence.
• Feed the workpiece in the direction of the grain.
• Remember to use the push stick when close to the cutterhead.
Thicknessing (fi g. A2, O1, O2)
1. Mount the guard/chip collector as described above.
2. Lower the guard (13).
3. Set the depth of cut.
4. Switch on the machine.
• Best results are achieved when the workpiece has at least one flat
surface.
• For optimal results, plane both sides of the workpiece to reach the
desired thickness.
E NG LISH
27