DeWalt D27300 Traduction De La Notice D'instructions Originale page 25

THICKNESS PLANER
D27300, D27300T
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
E
product development and innovation make D
reliable partners for professional power tool users.
Technical Data
Voltage
Type
Power input
Power output
No-load speed
Feed speed
Cutting height (max.)
Max. cutting width (max.)
Max. cutting depth
Planing mode
Thicknessing mode
Blade size
Weight
L (sound pressure)
PA
K (sound pressure
PA
uncertainty)
L (sound power)
WA
K (sound power
WA
uncertainty)
* at the operator's ear
Fuses:
Europe 230 V tools
400 V tools
NOTE (D27300 ONLY): This device is intended for the connection to
a power supply system with maximum permissible system impedance
Zmax of 0.27 Ω at the interface point (power service box) of user's
supply.
The user has to ensure that this device is connected only to a power
system which fulfils the requirement above. If necessary, the user can
ask the public power supply company for the system impedance at the
interface point.
Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
CAUTION: Used without the safety alert symbol indicates
a potentially hazardous situation which, if not avoided, may
result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
WALT one of the most
E
D27300 D27300T
V 230 400
2 2
W 2,100 3,000
W 1,650 2,280
max/min 6,200 6,200
-1
m/min 5 5
mm 160 160
mm 260 260
mm 2.5 2.5
mm 3 3
mm 20 20
kg 54 54
dB(A)* 96 96
dB(A) 3 3
dB(A) 109 109
dB(A) 3.1 3.1
16 Amperes, mains
16 Amperes, per phase
Denotes sharp edges.
EC-Declaration of Conformity
MACHINERY DIRECTIVE
D27300, D27300T
D WALT declares that these products described under "technical data"
E
are in compliance with:
2006/42/EC, EN 61029-1, EN 61029-2-3.
These products also comply with Directive 2004/108/EC. For more
information, please contact D
E
the back of the manual.
The undersigned is responsible for compilation of the technical file and
makes this declaration on behalf of D
Horst Grossmann
Vice President Engineering and Product Development
D WALT, Richard-Klinger-Straße 11,
E
D-65510, Idstein, Germany
01.02.2010
Safety Instructions
WARNING! When using electric tools basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury,
including the following.
Read all these instructions before attempting to operate this product
and save these instructions.
SAVE THIS MANUAL FOR FUTURE REFERENCE
General Safety Rules
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250–300 Lux). Do not use
the tool where there is a risk of causing fire or explosion, e.g., in the
presence of flammable liquids and gases.
3. Guard against electric shock.
Avoid body contact with earthed surfaces (e.g., pipes, radiators,
cookers and refrigerators). When using the tool under extreme
conditions (e.g., high humidity, when metal swarf is being
produced, etc.), electric safety can be improved by inserting an
isolating transformer or a (FI) earth-leakage circuit-breaker.
4. Keep other persons away.
Do not let persons, especially children, not involved in the work,
touch the tool or the extension cord and keep them away from the
work area.
5. Store idle tools.
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate to which it was
intended.
7. Use the right tool.
Do not force small tools to do the job of a heavy duty tool. Do
not use tools for purposes not intended; for example do not use
circular saws to cut tree limbs or logs.
WALT at the following address or refer to
WALT.
E
E N G L ISH
23