Publicité
Les langues disponibles
Les langues disponibles
EN GLIS H
8. Dress properly.
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Non-skid footwear is recommended when working
outdoors. Wear protective hair covering to contain long hair.
9. Use protective equipment.
Always use safety glasses. Use a face or dust mask if working
operations create dust or flying particles. If these particles might
be considerably hot, also wear a heat-resistant apron. Wear ear
protection at all times. Wear a safety helmet at all times.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust extraction and
collecting equipment, ensure these are connected and properly
used.
11. Do not abuse the cord.
Never yank the cord to disconnect it from the socket. Keep the
cord away from heat, oil and sharp edges. Never carry the tool by
its cord.
12. Secure work.
Where possible use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to operate the tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing
accessories. Inspect tools periodically and if damaged have
them repaired by an authorized service facility. Keep handles and
switches dry, clean and free from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing accessories
such as blades, bits and cutters, disconnect tools from the power
supply.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that adjusting keys and
wrenches are removed from the tool before operating the tool.
17. Avoid unintentional starting.
Do not carry the tool with a finger on the switch. Be sure that the
tool is in the "off" position before plugging in.
18. Use outdoor extension leads.
Before use, inspect the extension cable and replace if damaged.
When the tool is used outdoors, use only extension cords intended
for outdoor use and marked accordingly.
19. Stay alert.
Watch what you are doing. Use common sense. Do not operate the
tool when you are tired or under the influence of drugs or alcohol.
20. Check for damaged parts.
Before use, carefully check the tool and mains cable to determine
that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions that may
affect its operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service centre
unless otherwise indicated in this instruction manual. Have
defective switches replaced by an authorized service centre.
Do not use the tool if the switch does not turn it on and off.
Never attempt any repairs yourself.
WARNING! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
21. Have your tool repaired by a qualified person.
This electric tool complies with relevant safety rules. Repairs should
only be carried out by qualified persons using original spare parts;
otherwise this may result in considerable danger to the user.
24
Additional Safety Rules For Thickness Planers
• Wear safety goggles, working gloves and ear protection when
operating.
• Never operate the machine without all guards and anti-kickback
device in place and in perfect working condition.
• When planing, do not use the machine without the fence in
position. Make sure that the lower edge of the fence touches the
upper table top.
WARNING! The infeed and outfeed table were accurately
adjusted at the factory. Never change the setting of the tables
yourself.
• Use only cutting blades designed for this machine.
• Always use blades which are well sharpened and maintained.
• Do not use the machine for working any material other than soft
or hard wood.
• Never cut recesses, tenons or moulds. Rebating is not permitted.
• Never carry out stopped work (i.e., cuts that do not involve
working over the full length of the workpiece).
• Avoid working badly bowed wood providing inadequate contact
with the infeed table.
• Before use, check that the the kickback and feed spindles are
functioning properly.
• Remove all nails and metal objects from the workpiece before
starting work. Do not use splintery wood.
• In the planing mode, make sure the upper blade guard is
adjusted to provide optimum screening.
• Ensure that the elevating handle is out of the feed area.
• When working long pieces, use a suitable roller table on both
sides of the machine adjusted to the height of the tables.
• Keep your hands well clear of the blades.
• In the planing mode, use a push stick at all times.
• Keep the push stick in its place when not in use.
• Refrain from removing any cut-offs or other parts of the
workpiece from the cutting area whilst the cutter block is running.
• Workpiece sizes:
– Without additional support the machine is designed to accept
the maximum workpiece size of:
PLANER
– Height 140 mm by width 260 mm by length 500 mm
– Never cut workpiece shorter than 300 mm
THICKNESSER
– Height 160 mm by width 260 mm by length 600 mm
– Never cut workpiece shorter than 500 mm
– Longer workpiece needs to be supported by suitable
additional table, e.g., roller table.
• In case of an accident or machine failure immediately switch the
machine off and disconnect from socket.
• Report the failure and mark the machine in suitable form to
prevent other people from using the defective machine.
• PLANER ONLY: When the cutter block is blocked caused by
abnormal feed force during cutting, switch the machine off and
disconnect from power supply. Remove the workpiece and
ensure that the cutter block runs free. Switch the machine on and
start new cutting operation with reduced feed force.
• Ensure that any portion of the cutterblock not being used for
planing is safely guarded.
Residual Risks
The following risks are inherent to the use of planers:
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided.
These are:
– Risk of accidents caused by the uncovered parts of the rotating
blade.
Publicité
