Maintenance - Jacuzzi Designer Directives D'installation & D'utilisation

®
Magic Touch Whirlpool Switch
The Magic Touch whirlpool ON/OFF switch, conveniently located
on the bath, allows you to turn the whirlpool system on and off while
in the bath. Simply push down on the switch button to turn on the
whirlpool system. To turn the system off, push down on the button
again.
If your bath has an optional Jacuzzi Whirlpool Bath wall mounted
timer, set it for the amount of time you wish the whirlpool to operate.
Note: when you desire less than 10 minutes of whirlpool action, it is
necessary to turn the timer knob clockwise past the number 10 and
then back to the desired amount. If the whirlpool action does not
begin when the timer is correctly set, it is necessary to push the Magic
Touch switch button.
MAGIC TOUCH SWITCH
DEPRESS CENTER ON/OFF
Controlling Whirlpool Action
The whirlpool action in your bath is influenced by three factors –
direction of flow, force of water, and force of air. All baths manufac-
tured by Jacuzzi Whirlpool Bath are equipped with fully adjustable
PowerPro ® jets, which are adjustable for all three factors. Some baths
have additional directionally adjustable jets which can be adjusted for
direction and flow of air only.
Direction: To change the direction of the water flow, swivel the jet
nozzle to the desired angle. The jets can be directed individually
toward any location on your body to provide a hydromassage. The
jets can also be adjusted so that they all point in the same direction
(clockwise or counterclockwise) to circulate the water in a circular
motion around the bath, causing a total whirlpool effect.
Water Force: The high volume, fully adjustable jets can be ad-
justed to control the force of the water coming into the bath. For
robust action, increase the force of the flow by rotating the jet handles
to the left (counterclockwise). For a more gentle effect, rotate the
handles to the right (clockwise). Never run the whirlpool system
with all the jets closed.
Force of Air: Two knobs located on the bath serve as controls for
the air induction system. The intensity of the hydromassage whirl-
pool action is determined by the amount of air inducted into the water.
As the amount of air is increased, the hydromassage action increases.
For maximum air induction, rotate the control knobs fully counter-
clockwise to the largest circles. For fewer air bubbles, decrease the
amount of air induction by rotating the control knob clockwise. When
the knobs are turned to the smallest circles, only water is being circu-
lated.
JETS
DIRECTIONALLY
ADJUSTABLE
AIR INDUCTION CONTROLS
TURN CLOCKWISE TO
RAPID HEAT Operation
the heating function is totally automatic. The heater will help main-
tain the temperature of the water in the bath.
Vacuum Switch
allow the heater to turn ON if the pump is not running with water
flowing through the whirlpool system.
High-Limit Switch
circuit will not false trip from hot tap water. It will only turn off the
heater if the thermostat fails. To reset, press the button. If the high-
limit trips frequently, contact your dealer.

MAINTENANCE

Cleaning the Bath
gent solution. You can protect and restore the gloss to a dulled acrylic
surface by applying Meguiar's #10 Mirror Glaze, a product specifi-
cally designed for use on acrylic finishes. If Meguiar's is not avail-
able, an acrylic polish of equal quality or automotive paste wax is
acceptable.
pool Bath product.
Repairs to the Surface
removed by lightly sanding with 600-grit wet/dry sandpaper. Restore
the gloss using Meguiar's Mirror Glaze or automotive paste wax.
will require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for
special instructions.
Purging the Whirlpool System
tem, we recommend that you purge it every 3 to 4 months. To do this,
follow this simple procedure. Fill the bath with hot water (not exceed-
FULLY
ADJUSTABLE
ing 140°F). Add to the hot water 4 tablespoons of low foaming disin-
fectant. Turn the air induction completely OFF. Run the bath for 5 to
10 minutes. Drain the bath completely and refill with cold water only.
Run the whirlpool for 5 to 10 minutes, then drain the bath completely.
Bath Additives
Note: Do not use oil or oil-based bath additives.
of low-foaming powder or crystal substance; the whirlpool action in-
tensifies the foaming properties of soaps.
17
REDUCE AIR FLOW
Once the heater is installed and the whirlpool pump is operating,
The heater is equipped with a preset vacuum switch which will not
The heater includes an exclusive High-Limit switch. This safety
To clean your bath, simply use a mild, nonabrasive liquid deter-
Never use abrasive household cleaners on any Jacuzzi Whirl-
Minor scratches which do not penetrate the color finish can be
Major scratches and gouges which penetrate the acrylic surface
To remove accumulations of bath residue from the whirlpool sys-
If you want to use any kind of bath additive, use only a small amount
TURN COUNTER-CLOCKWISE
TO INCREASE AIR FLOW