Onkyo TX-8270 Mode D'emploi page 37

> Before Start > Part Names
GAME "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the GAME input selector. (Default Value is
"OPTICAL 1")
PC "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the PC input selector. (Default Value is "---")
CD "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the CD input selector. (Default Value is
"COAXIAL")
TV/TAPE "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the TV/TAPE input selector. (Default Value is
"OPTICAL 2")
PHONO "COAXIAL", "OPTICAL 1", "OPTICAL 2": Assign a desired
DIGITAL IN jack to the PHONO input selector. (Default Value is
"---")
0 Supported sampling rates for PCM signals (stereo, mono) from a digital input are 32 kHz,
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16 bit, 20 bit, 24 bit.
∫ 4. Analog Audio Input
You can change input assignment between the input selectors and AUDIO IN jacks. If you
do not assign a jack, select "---".
BD/DVD "AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the BD/DVD input selector. (Default Value is "---")
CBL/SAT "AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the CBL/SAT input selector. (Default Value is "---")
GAME "AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the GAME input selector. (Default Value is "---")
PC "AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the PC input selector. (Default Value is "AUDIO 1")
CD "AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the CD input selector. (Default Value is "AUDIO 3")
TV/TAPE "AUDIO 1", "AUDIO 2", "AUDIO 3": Assign a desired AUDIO IN
jack to the TV/TAPE input selector. (Default Value is "AUDIO 2")
> Install > Initial Setup > Playback
Advanced Setup
PHONO This setting is fixed at "PHONO" and cannot be changed.
2. Speaker
You can make changes to the connection environment of the speakers and volume level,
etc. This setting cannot be selected if headphones are connected or if "5. Hardware" -
"HDMI" - "Audio TV Out" is set to "On" so audio is output from the speakers of the TV.
∫ 1. Configuration
Subwoofer Set whether a subwoofer is connected or not.
"Yes (default value)": When subwoofer is connected
"No": When subwoofer is not connected
Speaker Impedance Set the impedance of the connected speakers.
"4ohms": When any of the connected speakers have 4 ≠ or
more to less than 6 ≠ impedance, or when a set of left and right
speakers are connected to each of the SPEAKERS A/B
terminals
"6ohms (default value)": When the connected speakers all have
6 ≠ or more impedance
0 For impedance, check the indications on the back of the
speakers or their instruction manual.
∫ 2. Crossover
Front Select the crossover frequency from "40Hz" to "200Hz" to start
outputting frequencies for each channel. (Default Value is
"100Hz")
"Full Band": Full band will be output.
0 If "Configuration" - "Subwoofer" is set to "No", "Front" will be
fixed to "Full Band".
Double Bass This can be selected when the "Front" setting is "Full Band".
Boost bass output by sending the bass of the front speakers to
the subwoofer.
"On": Bass output will be boosted.
"Off": Bass output will not be boosted.
| Supplementary Information | Others
37
En