Safety Features - BEGA BETEX Standard 22 ELDi SUPER Mode D'emploi

Safety features


The heater will switch off automatically if the ambient temperature exceeds 70ºC (158ºF).

When using the temperature mode, the heater will switch off automatically if the rate of
temperature rise is too low.

On models equipped with a swing arm, the arm can be fixed in the open position.
An induction heater works due a magnetic field. In the table below are there are some measured
values of the flux density in milliTesla (mT). These values are measured in different radii and heights
around the heater. These measurements can be used as a guide in conforming to local regulations
regarding the maximum time exposure of people to magnetic fields.
The values below are only valid for this combination of bearing type and yoke bar.
Different configurations may give different values. Due to the large variety of bearing types in
combination with the different yoke bars it is impossible for us to give every possible value.
Heater type Radius/height
R =250 mm
Model 22ELDi
R =500 mm
Yoke bar 40
R =750 mm
Bearing 6215
R =1000 mm
R =250 mm
Model 22ESDi
R =500 mm
Yoke bar 60
R =750 mm
Bearing 6219
R =1000 mm
R =250 mm
R =500 mm
Model 38ESD
Yoke bar 70 R =750 mm
Bearing 6222
R =1000 mm
R =1250 mm
Heater type Radius/height
R =250 mm
Model 38ZFD
R =500 mm
Yoke bar 80
R =750 mm
Bearing
R =1000 mm
229750/03
R =1250 mm
R =250 mm
R =500 mm
Model SUPER
Yoke bar 100 R =750 mm
Bearing RH24B
R =1000 mm
R =1250 mm
R =500 mm
R =750 mm
Model GIANT
Yoke bar 150 R =1000 mm
Bearing
R =1250 mm
17.52926
R =1500 mm
R =1750 mm
Heights are measured from the bottom of the heater. To determine where the field is exactly in relation
to the floor, the distance from the bottom of the heater to the floor should be added on to the values
mentioned in the table. (e.g. the height of a workbench).
WARNING!

We advise a safety distance of at least 1 meter for people.
CAUTION! The machine works through an induction field. Bear in mind that this can influence
electronic equipment, e.g. watches, magnetic charts etc.
h = 250 mm h = 500 mm
(10in) (20in)
0,785 mT 0,110 mT
0,054 mT 0,012 mT
0 mT 0 mT
0 mT 0 mT
2,950 mT 1,070 mT
0,310 mT 0,170 mT
0,500 mT 0,250 mT
00 mT 00 mT
6,800 mT 4,310 mT
0,935 mT 0,696 mT
0,204 mT 0,152 mT
0,034 mT 0,023 mT
0 mT 0 mT
h = 900 mm h=1300 mm
*
(10in)
5,800 mT 0,750 mT
1,070 mT 0,320 mT
0,345 mT 0,141 mT
0,121 mT 0,054 mT
0,030 mT 0,006 mT
6,400 mT 4,100 mT
1,308 mT 1,050 mT
0,350 mT 0,298 mT
0,116 mT 0,093 mT
0,030 mT 0,017 mT
1,980 mT 1,375 mT
0,530 mT 0,450 mT
0,180 mT 0,180 mT
0,070 mT 0,030 mT
0,020 mT 0,020 mT
0 mT
h = 750 mm
(30in)
0 mT
0 mT
0 mT
0 mT
0,120 mT
0,050 mT
0 mT
0 mT
0,590 mT
0,230 mT
0,059 mT
0,003 mT
0 mT
h=1500 mm
(51in) (59in)
0,253 mT
0,134 mT
0,068 mT
0,020 mT
0 mT
1,460 mT
0,530 mT
0,186 mT
0,063 mT
0,010 mT
1,020 mT
0,370 mT
0,160 mT
0,030 mT
0,010 mT
0 mT 0 mT
6
h =1000 mm h = 1250 mm
40in) (49in)
0 mT 0 mT
0 mT 0 mT
0 mT 0 mT
0 mT 0 mT
0 mT 0 mT
0 mT 0 mT
0 mT 0 mT
0 mT 0 mT
0,110 mT 0 mT
0,042 mT 0 mT
0 mT 0 mT
0 mT 0 mT
0 mT 0 mT
h =2000 mm
(79in)
0,010 mT
0 mT
0 mT
0 mT
0 mT
0,150 mT
0,105 mT
0,037 mT
0,010 mT
0 mT
0,340 mT
0,170 mT
0,080 mT
0,030 mT
0 mT
0 mT