Black & Decker BL188 Mode D'emploi page 6

ENGLISH
Warning! fire Hazard. When disconnecting the charger from
the tool, be sure to unplug the charger from the outlet first,
then disconnect the charger cord from the tool.
To install battery pack - Figure B
Insert battery pack firmly into tool until an audible click is
u
heard as shown in figure B. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack - Figure B insert
Depress the battery release button (7) as shown in figure
u
B1 and pull battery pack out of tool.
Trigger switch & forward/reverse button - figure C
The drill is turned ON and OFF by pulling and releasing
u
the trigger switch (1) shown in figure C. The farther the
trigger is depressed, the higher the speed of the drill.
A forward/reverse control button (2) determines the
u
rotational direction of the tool and also serves as a lock off
button.
To select forward rotation, release the trigger switch and
u
depress the forward/reverse control button on the right
side of the tool.
To select reverse, depress the forward/reverse control
u
button on the left side of the tool.
The center position of the control button locks the tool in
u
the off position. When changing the position of the control
button, be sure the trigger is released.
Adjusting torque control - figure D
This tool is fitted with a torque adjustment collar (3) to select
the operating mode and to set the torque for tightening
screws. Large screws and hard workpiece materials require
a higher torque setting than small screws and soft workpiece
materials.
For drilling in wood, metal and plastics, set the collar to
u
the drilling position symbol.
For screwdriving, set the collar to the desired setting.
u
If you do not yet know the appropriate setting, proceed as
follows:
Set the collar to the lowest torque setting.
u
Tighten the first screw.
u
If the clutch ratchets before the desired result is
u
achieved, increase the collar setting and continue
tightening the screw.
Repeat until you reach the correct setting.
u
Use this setting for the remaining screws.
u
Dual range switch - figure E
The dual range feature of your drill allows you to shift gears
for greater versatility.
6
(Original instructions)
To select low speed, high torque setting (position1),
u
turn tool off and permit to stop. Slide gear shifter button (4)
away from the chuck.
To select the high speed, low torque setting (position
u
2), turn tool off and permit to stop. Slide gear shifter but-
ton back toward the chuck.
Note: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual range
gear button is either completely pushed forward or completely
pushed back.
keyless chuck - figure F
Warning! Make certain the battery pack is removed to prevent
tool actuation before installing or removing accessories.
To insert a drill bit or other accessory:
Grasp the chuck (5) and rotate it in the counterclockwise
u
direction, as viewed from the chuck end.
Insert the bit or other accessory fully into the chuck, and
u
tighten securely by rotating the chuck in the clockwise
direction as viewed from the chuck end.
Warning! Do not attempt to tighten or loosen drill bits (or any
other accessory) by gripping the front part of the chuck and
turning the tool on. Damage to the chuck and personal injury
may occur when changing accessories.
Hammer Action
The BL188 drill has hammer action which is engaged by
twisting the collar to the hammer symbol
hammer action when drilling in masonry.
Warning! When the torque adjustment collar is in the drill or
hammer drill positions, the drill will not clutch. The drill may
stall if overloaded, causing a sudden twist.
Screw driving
For driving fasteners, the forward/reverse button should
u
be pushed to the left.
Use reverse (button pushed to the right) for removing
u
fasteners.
Note: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
Drilling
Use sharp drill bits only.
u
Support and secure work properly, as instructed in the
u
Safety Instructions.
Use appropriate and required safety equipment, as
u
instructed in the Safety Instructions.
Secure and maintain work area, as instructed in the
u
Safety Instructions.
Run the drill very slowly, using light pressure, until the
u
hole is started enough to keep the drill bit from slipping out
of it.
q
. Use