Monacor TVSP-42COL Mode D'emploi page 12

QUAD button (5) pressed and additionally actuate the
GB
MENU button. The TVSP-42COL now switches to the
respective other video standard. The current video
standard is displayed at the left bottom of the first page
of the setting menu. If the adjusted video standard of
the TVSP-42COL does not correspond to that of the
monitor, the picture on the monitor rolls up or down in
black and white.
5.2.2 Setting menu, page 2
SEQUENTIAL SWITCH MENU
SEQUENCE :
Q 1 2 3 4 - - -
DWELL TIME :
3 3 3 3 3 3 3 3 SEC
-----------------------
BUZZER : ON
FREEZE HOLD TIME:3O SEC
DUPLEX MODE : HALF
The following parameters can be adjusted on this
menu page:
SEQUENCE allows programming of any sequence
of up to eight pictures for the automatic sequential
switching (operating mode "Automatic"). The options
are the frames of the individual cameras ("1", "2", "3",
"4") and the quad picture ("Q"). Positions with the
option "-" are skipped by the unit.
DWELL TIME defines the individual dwell time of 1 to
9 s for each picture selected in the line SEQUENCE.
BUZZER defines whether the loss of a video signal
due to failure of a camera is to be indicated by an
acoustic signal (ON) or not (OFF). In addition, it is pos-
sible to define the duration of the acoustic signal (1 to
99 min.) if it is not switched off by pressing any button.
FREEZE HOLD TIME defines the time of the TVSP-
42COL in the still picture mode before returning auto-
matically to the operating mode "Normal". However, it
is possible at any time to change the operating mode
manually. A time between 1 and 99 s can be selected.
If 0 s is adjusted, the operating mode "Still picture"
remains until it is left manually.
DUPLEX MODE allows the following settings:
HALF In the reproduction mode, a frame display of
the recorded quadrants is possible, however, no
simultaneous reproduction of the current camera
pictures via the jack QUAD OUT (10).
FULL In the reproduction mode, no frame display of
the recorded quadrants is possible. Thus, a contin-
uous reproduction of the current camera pictures
via the jack QUAD OUT for recording on another
video recorder is ensured.
12
O1 MIN
5.2.3 Setting menu, page 3
BRIGHT 16 BRIGHT
CONTRAST 42 CONTRAST O5
CHROMA 63 CHROMA
SHARP O4 SHARP
BRIGHT 26 BRIGHT
CONTRAST 63 CONTRAST 45
CHROMA OO CHROMA
SHARP 44 SHARP
On this menu page, the following values for each
camera picture can be adjusted separately:
BRIGHT
CONTRAST
CHROMA
SHARP
All values are adjustable from 0 to 64.
5.3 Total reset of the unit/
Summary of the presettings
A total reset of the TVSP-42COL to the factory-set
values is possible. For this purpose, press the MENU
button (8). The LED above the button lights up. Then
keep the button PLAY (7) pressed and additionally
actuate the MENU button (8).
Attention: Activation of this option results in irretrieva-
ble loss of all settings made by the user. They are
replaced by the factory-set values.
The factory-set values are summarized in the table
below:
Presettings
DATE FORMAT
DATE
LOCATION
TIME
TITLE
TITLES
VIDEOSYSTEM
TEST PATTERN COLOR BAR OFF
SEQUENCE
DWELL TIME
BUZZER
FREEZE HOLD TIME
DUPLEX MODE
BRIGHT
CONTRAST
CHROMA
SHARP
19
24
55
11
21
OO
YY/MM/DD
ON
BOTTOM
ON
ON
1, 2, 3, 4
PAL
Q 1 2 3 4 - - -
3 3 3 3 3 3 3 3 SEC
ON, 1 MIN
30 SEC
HALF
16
42
18
04