Napa 6-1072 Instructions page 2

FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY.
This insTrucTion Manual
conTains iMporTanT safeTy
inforMaTion.
read This
insTrucTion
Manual
carefully and
undersTand all inforMaTion
Before operaTing This Tool.
• Always operate, inspect and
maintain this tool in accordance
with American National Standards
Institute Safety Code of Portable
Air Tools (ANSI B186.1) and any
other applicable safety codes
and regulations.
• For safety, top performance and
max­imum durability of parts,
operate this tool at
90 psig, 6.2 bar max­
air pressure with 3/8"
diameter air
supply hose.
• Always wear impact-resistant
eye and face
protection when
operating or
performing
maintenance on this
tool.
• High sound levels can cause
permanent hearing loss.
Always use hearing
protection as
recommended by
your employer and
OSHA regulations
while using this tool.
• Keep the tool in efficient
operating condition.
• Operators and maintenance
personnel must be physically
able to handle the bulk, weight
and power of this tool.
• Compressed air can cause severe
injury. Never direct air at
yourself or others. Always turn
off the air supply, drain hose
PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE ThIS mANUAL fOR fUTURE REfERENCE.
6-1072
of air pressure, and detach tool
from air supply before
installing, removing, or
adjusting any part or
accessory on this tool,
or before performing
any maintenance on this tool.
Failure to do so could
result in injury. Whip
hoses can cause serious
injury. Always
check for and replace
any damaged, frayed,
or loose hoses and
fittings. Do not operate a
damaged or worn
tool. Do not use
q­uick-detach couplings
at tool. See instructions
for correct setup.
• Air-powered tools can vibrate
during use. Ex­tended ex­posure
to vibration, repetitive motions,
or uncomfortable
positions during use
may be harmful to
your hands and arms.
Discontinue use of tool
if discomfort, tingling,
or pain occurs. Seek medical
advice before resuming use.
• Place the tool on the work
before starting the tool. Do not
point or indulge in any horseplay
with this tool.
• Slipping, tripping and/or falling
while operating air tools can be
a major cause of
serious injury or death. Be aware
of ex­cess hose left on
the walking or work
surface.
• Keep body working
stance balanced and
firm. Do not overreach when
operating the tool.
• Anticipate and be alert for sudden
changes in motion during use of
any power tool.
2
• Do not carry tool by the hose.
Protect the hose from sharp
objects and heat.
• Tool shaft may
continue to rotate
briefly after throttle is
released. Avoid direct
contact with
accessories during and after use.
Gloves will reduce the risk of
cuts or burns.
• Keep away from rotating end
of tool. Do not wear jewelry
or loose clothing. Secure long
hair. Scalping can occur if hair is
not kept away from
tool and accessories.
Choking can occur if
neckwear is not kept
away from tool and
accessories.
• Do not lubricate tools with
flammable or volatile liq­uids
such as kerosene, diesel or jet
fuel.
• Impact wrenches are not torq­ue
control devices. Fasteners with
specific torq­ue req­uirements
must be checked with suitable
torq­ue measuring devices after
installation with an impact
wrench.
• Use only impact wrench sockets
and accessories on this tool. Do
not use hand sockets and
accessories, as they may be
damaged or cause damage to the
eq­uipment or operator.
• Do not force tool beyond its
rated capacity.
• Do not remove any labels.
Replace any damaged labels.
• Use accessories recommended by
NAPA Professional Air Tools.
Rev. 08/11/06