Ec Declaration Of Conformity - Makita M9400 Manuel D'instructions

Masquer les pouces Voir aussi pour M9400:

Manuel d'instructions (15 pages)

Table Des Matières

Table des Matières

Les langues disponibles

Installing or removing abrasive belt (Fig. 2 & 3)

Pull the lever all the way out and install the belt over the

rollers, and then return the lever to the original position.

CAUTION:

• When installing the belt, make sure that the direction of

the arrow on the back of the belt corresponds to the

one on the tool itself.

Installing or removing step (Fig. 4)

Using step with the tool turned upside down allows

sanding another way of use. Remove the knob and then

place the step on the place the knob was seated and

secure it with knob.

Adjusting belt tracking (Fig. 5)

While the belt is running, use the adjusting knob to center

the belt tracking. Failure to do so can result in frayed belt

edges and wear on the sander frame.

Dust bag (Fig. 6)

The use of the dust bag makes sanding operations clean

and dust collection easy. To attach the dust bag, fit it onto

the dust spout.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust

bag of its contents, tapping it lightly so as to remove

particles adhering to the insides which might hamper

further collection.

OPERATION

Sanding operation (Fig. 7)

CAUTION:

• The tool should not be in contact with the workpiece

surface when you turn the tool on or off. Otherwise a

poor sanding finish or damage of the belt may result.

Hold the tool firmly with both hands. Turn the tool on and

wait until it attains full speed. Then gently place the tool

on the workpiece surface. Keep the belt flush with the

workpiece at all times and move the tool back and forth.

Never force the tool. The weight of the tool applies

adequate pressure. Excessive pressure may cause

stalling, overheating of the motor, burning of the

workpiece and possible kickback.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon plate (Fig. 8)

Replace an carbon plate on the cork rubber plate when it

is worn down. Remove screws on the strap washer and

the worn carbon plate, place a new carbon plate and

then secure it with the screws.

Replacing carbon brushes (Fig. 9 & 10)

Remove and check the carbon brushes regularly.

Replace them when they are worn down to the limit

mark. Keep the carbon brushes clean and free to slip in

the holders. Both carbon brushes should be replaced at

the same time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

Noise

The typical A-weighted noise level determined according

to EN62841:

Sound pressure level (L

Sound power level (L

Uncertainty (K): 3 dB (A)

NOTE:

• The declared noise emission value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

• The declared noise emission value(s) may also be

used in a preliminary assessment of exposure.

WARNING:

• Wear ear protection.

• The noise emission during actual use of the power

tool

can

differ

from

depending on the ways in which the tool is used

especially what kind of workpiece is processed.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it

is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN62841:

Work mode: sanding metal plate

Vibration emission (a

Uncertainty (K): 1.5 m/s

NOTE:

• The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

• The declared vibration total value(s) may also be used

in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared value(s)

depending on the ways in which the tool is used

especially what kind of workpiece is processed.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it

is running idle in addition to the trigger time).