Reference Information - Makita DRC200 Manuel D'instructions

REFERENCE
INFORMATION
Makita Corporation and its subsidiaries, affiliates, and
distributors may use Usage Information for the purpose
of after-sales services such as maintenance and repair.
Usage Information consists of number of operations,
distribution load, error information, operational status,
and/or maintenance record of the power tool.
Contains FCC ID: GT3FC020
FCC CAUTION
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate the equipment.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and
receiver.
— Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV
technician for help.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which
is the passed down through the MAC, through the
digital and analog baseband, and finally to the RF chip.
Several special packets are initiated by the MAC. These
are the only ways the digital baseband portion will turn
on the RF transmitter, which it then turns off at the
end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being
transmitted. In other words, this device automatically
discontinue transmission in case of either absence of
information to transmit or operational failure.
Contains IC: 3683A-FC020
Compliance with IC requirement RSS-210 A9.4.4
Data transmission is always initiated by software, which
is the passed down through the MAC, through the
digital and analog baseband, and finally to the RF chip.
Several special packets are initiated by the MAC. These
are the only ways the digital baseband portion will turn
on the RF transmitter, which it then turns off at the
end of the packet. Therefore, the transmitter will be on
only while one of the aforementioned packets is being
transmitted. In other words, this device automatically
discontinue transmission in case of either absence of
information to transmit or operational failure.
Conformité à la norme CNR-210 A9.4.4
La transmission des données est toujours initiée
par le logiciel, puis les données sont transmises
par l'intermédiaire du MAC, par la bande de base
numérique et analogique et, enfin, à la puce RF.
Plusieurs paquets spéciaux sont initiés par le MAC. Ce
sont les seuls moyens pour qu'une partie de la bande
de base numérique active l'émetteur RF, puis désactive
celui-ci à la fin du paquet. En conséquence, l'émetteur
reste uniquement activé lors de la transmission d'un
des paquets susmentionnés. En d'autres termes,
ce dispositif interrompt automatiquement toute
transmission en cas d'absence d'information à
transmettre ou de défaillance.
This device complies with Part 15 of FCC Rules and
Industry Canada's licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation of this device.
Le présent appareil est conforme aux la partie 15
des règles de la FCC et CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le
fonctionnement.
This equipment complies with FCC/IC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment has
very low levels of RF energy that are deemed to comply
without testing of specific absorption rate (SAR).
Cet équipement est conforme aux limites d'exposition
aux rayonnements énoncées pour un environnement
non contrôlé et respecte les règles les radioélectriques
(RF) de la FCC lignes directrices d'exposition et
d'exposition aux fréquences radioélectriques (RF)
CNR-102 de l'IC. Cet équipement émet une énergie RF
très faible qui est considérée conforme sans évaluation
du débit d'absorption spécifique (DAS).
15 ENGLISH