Throttle Trigger - Husqvarna 125B Manuel D'utilisation

Masquer les pouces Voir aussi pour 125B:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Always use new unleaded gasoline with a minimum
octane number of 90 RON (87 AKI) and with less
than 10% ethanol concentration (E10).
Use gasoline with a higher octane number if you
frequently use the product at continuously high
engine speed.
Always use a good quality unleaded gasoline/oil
mixture.
Two-cycle engine oil
Use only high quality two-cycle engine oil. Use only
an air cooled engine oil.
Do not use other types of oil.
Mixture ratio 50:1 (2%)
Gasoline
1 U.S. Gal.
1 UK Gal.
5 l
To make the fuel mixture
Note: Always use a clean fuel container when you mix
the fuel.
Note: Do not make more than 30 days quantity of fuel
mixture.
1. Add half of the gasoline quantity.
2. Add the full quantity of oil.
3. Shake the fuel mixture to mix the contents.
4. Add the remaining gasoline quantity.
5. Shake the fuel mixture to mix the contents.
6. Fill the fuel tank.
To add fuel
Always use a fuel container with an antispill valve.
If there is some fuel on the container, remove the
unwanted fuel and let the container dry.
Make sure that the area near the fuel tank cap is
clean.
Shake the fuel container before you add the fuel
mixture to the fuel tank.
To start and stop
Before you start the engine
Examine the product for missing, damaged, loose or
worn parts.
Examine the collection bag. Make sure that the
collection bag is not damaged and that the zipper is
closed.
Examine the nuts, screws and bolts.
Examine the air filter.
214 - 007 - 16.12.2019
Oil
77 ml (2,6 oz)
95 ml (3,2 oz)
100 ml (3,4 oz)
Examine the throttle trigger for correct operation.
Examine the stop switch for correct operation.
Examine the product for fuel leaks.
To start a cold engine
WARNING: Do not wind the starter rope
around your arm.
CAUTION: Do not hold the product with your
foot.
CAUTION: Do not pull the starter rope to the
end position. Do not let go of the starter rope
handle when the starter rope is extended.
This can damage the product.
Note: If the engine stops, move the choke control to the
closed position and do the starting steps again.
1. Fill the fuel tank with a clean fuel mixture.
2. Push the primer bulb 10 times. (Fig. 20)
3. Move the engine choke control to the FULL CHOKE
(closed) position. (Fig. 21)
4. Push the variable speed control fully
counterclockwise. (Fig. 22)
5. Use your left hand to hold the body of the machine
on the ground.
6. Pull the starter rope handle until the engine tries to
run. Do not pull more than 3 times.
7. Move the choke control to the 1/2 position and pull
the starter rope handle until the engine starts and
runs. (Fig. 23)
8. Run the engine for approximately 10 seconds.
9. Push and hold the throttle trigger fully through all
remaining steps.
10. Move the choke control to the OFF CHOKE
(opened) position. (Fig. 24)
11. Warm the engine up for 1 minute.
To start a warm engine
1. Push and hold the throttle trigger.
2. Move the choke control to 1/2 position.
3. Pull the starter rope handle quickly while you pull the
throttle trigger until the engine runs.
4. Move the choke control to the OFF CHOKE
(opened) position.
To stop the engine
Push and release the engine STOP switch. The
switch automatically returns to the ON position. Wait
11

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

125bx125bvx

Table des Matières