Desoutter ERP250 Mode D'emploi page 6

Safety Information
3 LEDs
4 Tool cable connector
5 Trigger
6 Headlight
7 Mounting location of the side handle
8 Spline
Dimensions
D
ØC
ØA
ØB
ERP250 ERP500 ERP750
A (mm) 54 67
A (") 2.13 2.64
B (mm) 54 54
B (") 2.13 2.13
C (mm) 70 70
C (") 2.76 2.76
D (mm) 407 438
D (") 16.02 17.24
E (mm) 275 275
E (") 10.83 10.83
F (mm) 71 71
F (") 2.80 2.80
Connecting the power cable
Connect the power cable to the tool and lock the nut by hand.
Connecting the tool to the controller
Switch off the controller before connecting or discon-
necting the tool cable and the adaptor from the con-
troller.
Refer to the user manual 6159921160 available at
www.desouttertools.com/resource-centre.
F
ERP100 ERP170
0 0
67 67 84
2.64 2.64 3.31
54 54 54
2.13 2.13 2.13
70 70 70
2.76 2.76 2.76
455 468 501
17.91 18.43 19.72
275 275 275
10.83 10.83 10.83
71 71 71
2.80 2.80 2.80
https://
Installing the torque reaction bar
Mount the torque reaction bar before powering on the
tool.
70 Nm
ERP250
ERP500 90 Nm
100 Nm
ERP750
ERP1000 100 Nm
120 Nm
ERP1700
1. Select the type of reaction bar according to the number
E
of splines of the tool. Refer to chapter Number of
splines.
2. Use one of the reaction bars proposed as optional ac-
cessories (refer to Optional accessories). If not, read
and follow the instructions about how to select and
shape a reaction bar in the chapter --- MISSING LINK
---.
3. Unscrew the nut of the gear housing.
4. Place the reaction bar on the gear housing.
5. Tighten the nut of the gear housing according to the
torque values given in the diagram.
NOK
A
E+15°
15°
Axe BE
E
15°
E-15°
K
45°
40°
35°
30°
25° 15°
OK
A
E+15°
15°
K
Axe BE
E
15°
E-15°
45°
40°
35°
30°
25°
15°
Follow the instructions given in the above diagram.
Starting the tool
Fit the tool with a suitable socket.
Select the appropriate program on the controller.
Hold the tool by means of the handle, place the reaction bar
on a suitable reaction point and apply to the fastener to be
tightened.
WARNING Risk of Injury
As the reaction force increases in proportion to the tight-
ening torque, there is a risk of severe bodily injury of the
operator as a result of unexpected behavior of the tool.
Make sure that the tool is in perfect working order
►
and the controller is programmed correctly.
6 / 144
NOK
TR
L K
DV E+15°
B
15°
Axe BE
E
C
15°
E-15°
45° 40° 30° 25° 15°
35°
OK
TR
E+15°
L
K
15°
DV
Axe BE
E
B
15°
45°
E-15°
40°
C
35°
30°
A
TR
L
DV
B
C
A
TR
L
DV
B
25° C
15°
04/2022