Technical Data - Milwaukee DR 350 T Notice Originale

TECHNICAL DATA

DRILL STAND
Usable Column length ............................................................
Bevel.......................................................................................
Drilling capacity max...............................................................
Length/Width/Height ...............................................................
Weight according EPTA-Procedure 01/2014 ..........................
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DIAMOND DRILL SAFETY WARNINGS
When performing drilling that requires the use of water,
route the water away from the operator's work area or
use a liquid collection device. Such precautionary
measures keep the operator's work dry and reduce the risk
of electrical shock.
Operate power tool by insulated grasping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
Wear hearing protection when diamond drilling.
Exposure to noise can cause hearing loss.
When the bit is jammed, stop the applying downward
pressure and turn off the tool. Investigate and take
corrective actions to eliminate the cause of the bit jamming.
When restarting a diamond drill in the workpiece check
that the bit rotates freely before starting. If the bit is
jammed, it may not start, may overload the tool, or may
cause the diamond drill to release from the workpiece.
When securing the drill stand with anchors and
fasteners to the workpiece, ensure that the anchoring
used is capable of holding and restraining the machine
during use. If the workpiece is weak or porous, the anchor
may pull out causing the drill stand to release from the
workpiece.
When securing the drill stand with a vacuum pad to the
workpiece, install the pad on a smooth, clean,
non-porous surface. Do not secure to laminated
surfaces such as tiles and composite coating. If the
workpiece is not smooth, fl at or well affi xed, the pad may
pull away from the workpiece
Ensure there is suffi cient vaccum before and during
drilling. If the vacuum is insuffi cient, the pad may release
from the workpiece.
Never perform drilling with the machine secured by the
vacuum pad only, except when drilling downwards. If
the vaccum is lost, the pad will release from the workpiece.
When drilling through walls or ceilings, ensure to
protect persons and the work area on the other side.
The bit may extend through the hole or the core may fall
out on the other side.
Do not use this tool for overhead drilling with water
supply. Water entering the power tool will increase the risk
of electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
When coring through fl oors, cores generally drop from the
bit. Provide proper protection for people and property below
the coring area.
Use protective equipment. Always wear safety glasses
when working with the machine. The use of protective
clothing is recommended, such as dust mask, protective
gloves, sturdy non-slip footwear, helmet and ear defenders.
22 ENGLISH
DR 350 TV
..................................... 610 mm
.................................... 0-45 °
..................................... 350 mm
................391 x 523 x 1042 mm
.................................... 19,5 kg
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the
machine is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
SPECIFIED CONDITIONS OF USE
The diamond drill stand is intended for use with Milwaukee
diamond drills. It must be attached to the fl oor or wall by
means of vacuum or anchors.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2006/42/EC and the following
harmonized standards have been used:
EN 62841-1:2015
EN 62841-3-6:2014+A11:2017
Winnenden, 2020-11-05
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under "Technical Data" fulfi lls all
the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I.
2012/3032 (as amended) and that the following designated
standards have been used:
BS EN 62841-1:2015
BS EN 62841-3-6:2014+A11:2017
Winnenden, 2020-11-05
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
WATER CONNECTION
Core drilling requires the application of water. Supply an
adequate water fl ow!
An adequate supply of water must fl ow freely and
constantly during the entire cut. This Coring Motor are
equipped with a built-in water passage to allow water to
fl ow down the inside and up around the outside of the bit.
This acts to cool the bit and fl ush cuttings from the hole.
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Wear gloves!
Wear ear protectors!
Always wear goggles when using the machine.
Wear a protective helmet.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 23