Battery Charging - HP Autozubehor 20360 Mode D'emploi

2. INTRODUCTION
Cordless random orbital polisher with Ø240mm foam pad and polishing bonnet. Smooth operation provides even buffing/polishing with no hot spots.
Adjustable handles provide a choice of 3 working positions, making it suitable for various tasks. Impact resistant housing with soft grip handles.
Supplied with 18V Lithium-ion battery pack and battery charger.
3. SPECIFICATION
Model no:..........................................................................20360
Battery:............................................................18V 2.0Ah Li-ion
Speed:......................................................................... 2500rpm
Pad size:......................................................................Ø240mm
Replacement battery pack:.....................................CP2518LBP
Replacement backing pad:................................. CP2518L.SBP
Replacement bonnet terry cloth:.............................ER230P.TB
Replacement bonnet synthetic fleece:................CP2518L.BSF
Noise power:...................................................................88dBA
Noise pressure:...............................................................77dBA
Vibration:....................................................................3.325m/s²
Uncertainty:....................................................................1.5m/s²
4. OPERATION
IMPORTANT WARRANTY INFORMATION:
The battery pack fitted to this cordless tool is considered to be a consumable item and its ability to accept charge will reduce over time. We
will warranty it against mechanical and electrical defect for a period of one year - this does not cover fair wear and tear. If the battery is not
properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace the
battery pack even if it is less than one year old.

4.1. BATTERY CHARGING

4.1.1. Plug the charger into a mains electric socket. When switched on, the left hand charger LED will be red.
4.1.2. To release the battery press the battery latch and slide the battery out.
4.1.3. Slide the battery into the charger.
4.1.4. Whilst charging the left hand LED will be green and the right hand LED will be red.
4.1.5. When fully charged the left LED will go off and the right hand LED will be green.
4.1.6. Refit the battery into the polisher, ensure it clicks home.
Note: When new, the battery may have been shipped in a low charge state. It will take longer to charge the battery initially and several subsequent
charges may also take a little longer, compared with when the battery reaches its optimum performance.
4.2. OPERATION
WARNING! Ensure that you read, understand and apply the safety instructions in Section 1.
WARNING! Do not use the polisher with abrasive or rubbing compounds.
WARNING! Excess pressure can cause damage to paintwork and will put the polisher motor under strain. Polishers returned with burnt out
motors will be rejected as a warranty claim. Normally the weight of the polisher is sufficient.
4.2.1. Regularly check that the bonnet is clean and free of abrasive particles and is undamaged and that the pad rotates freely.
4.2.2. Apply a small amount of polish/wax evenly over the surface of the bonnet. DO NOT apply polish directly to the vehicle surface.
4.2.3. Hold the polisher firmly by the handles and place the polishing face onto the panel to be polished.
4.2.4. S tart the polisher using the switch built into the underside of the right hand handle. Squeeze and hold the switch ensuring that the pad is still in
contact with the vehicle panel.
4.2.5. Move the polisher with broad sweeping strokes over the surface in a criss-cross pattern. DO NOT apply pressure to the polisher when in use.
Work in logical areas and re-apply the polish/wax at intervals during the polish application process. DO NOT allow the foam pad to become saturated
with polish/wax as this will make polishing more difficult and will reduce pad life.
4.2.6. Polish/wax should be applied to difficult-to-reach areas by hand.
4.2.7. Switch Off the polisher by releasing the ON/OFF switch before lifting it from the panel when polish application is completed.
4.2.8. Remove the application bonnet and replace it with the wool bonnet.
4.2.9. Buff the polish/wax in the same order it was applied. DO NOT put pressure on the polisher but allow its weight and action to do the job.
4.2.10. Badly oxidised paint may require several applications. DO NOT use abrasive compounds.
4.2.11. If the polish/wax is difficult to buff too much has been applied. This may also cause the bonnet to come off the pad.
WARNING! DO NOT immerse the polisher in water.
3