Table des Matières
Publicité
OPERATING NOTES | CONSIGNES DE FONCTIONNEMENT | ISTRUC
GAS MELTER
EN
USES:
To melt different kind of fillers (Hard Wax, Hard Wax PLUS, Hard Wax Matt,
Ceramic-Filler). Also for levelling and colour mixing.
TECHNICAL SPECIFICATION:
Length: 177 mm • Weight: 60 g • Operating time (typical): approx. 90 min-
utes • Tip temperature: up to 240°C • Refill time: approx. 10 seconds • Gas:
lighter fuel • Tip selection: 2 pieces • Flint-ignitor: integrated • Ignitor life:
approx. 1000 cycles • Safety cut-off switch • Temperature adjustable • One-
year guarantee.
BEFORE SETTING TO WORK:
Read entire operating and safety instructions!
Gas Melteris being supplied in unfilled condition. Only use quality lighter
gas.
Caution: The tip turns hot during operation. Risk of burning! The Gas
Melter is filled with flammable gas. Please handle with care.
INSTRUCTIONS FOR USE:
1. Putting into service: Set the temperature regulator to highest position,
hold tip away from face and body. Turn the on-off switch 'ON' (push to-
wards tip direction - this will open the gas valve). Ignite emitted gas with
the flint. It flames for a few seconds - until the catalyst begins to glow.
Note: Should the flame not extinguish within 30 seconds the catalyst is
used up and the tip has to be replaced with a new one.
2. Temperature setting: Approximate guide number: mid position for Hard
Wax, turn to '-' direction for Soft Wax, turn to '+' direction for Hard Wax
Matt and PLUS and for Ceramic Filler. Note: If bubbles or smoke develops
during melting the temperature has to be set down.
3. Processing filler material: Always melt off small portions of filler, only.
Do not let filler drop but take off with the tip and press it into the damage
area. This ensures a precise work. After filling level projectings carefully
and continue procedure according to the instructions for use of the relevant
filler material. Note: The catalyst tip is subject to wear and tear. Take care
not to let wax enter into the delicate catalyst material - life time of the tip
will be prolonged.
Do not remove possible soilings on the catalyst mechanically - this would
destroy the catalyst. In case of soilings turn off the gas flow and take a
lighter to burn the catalyst 'free'. Then put again into operation and let
remaining wax residues glow off - set temperature to full power and wait
until no smoke develops any more. As soon as normal operation tempera-
ture is achieved, melting procedure can continue.
4. After use: turn off gas flow (on-off switch towards 'OFF'), wait until tip
has cooled and replace cap. Remove wax residues on the still heated tip
FER À FONDRE
FR
DOMAINE D'APPLICATION :
La fonte des produits de remplissage König (Cire Dure, Cire Dure Mate, Cire
Dure PLUS, Kerami-Fill
) et pour égaliser et mélanger les couleurs.
®
CARACTÉRISTIQUES TECHNIQUES :
Longueur: 177 mm • Poids: 60 g • Durée de brûlage: env. 90 min (selon de le
réglage) • Température des pointes: jusqu'à 240°C • Temps de remplissage:
carefully with wire wool or a cotton cloth. Because of the risk of ignition
make sure that the tool is turned off before using wire wool!
SPARE PARTS AVAILABLE:
Catalyst tip, 1 piece
Flint, 12 pieces
ACCESSORIES AVAILABLE:
Refill gas – 100 ml can
Special Tip, 1 pc.
RE-FILLING GAS:
A gas refill adapter is normally not required. Make sure the on-off switch is
in the off position before filling. Stand unit vertically with the filling valve
face upwards. Push the gas re-fill cylinder onto the filling valve. A hiss sig-
nals the end of the filling procedure (after approx. 10 seconds).
Due to legal regulation the
REPLACEMENT OF THE CATALYST TIP:
Turn off tip coupling, take off tip and screw on new one.
REPLACEMENT OF THE FLINT:
Remove Phillips screw at top of the cap, take off spark wheel, replace flint
and put the parts together again.
SAFETY WARNINGS:
1. The Gas Melter contains flammable gas under pressure. Do not
2. Do not puncture or incinerate.
3. Keep out of reach of children.
4. To re-fill use a high quality butane cigarette lighter fuel.
5. Do not re-fill or ignite in the vicinity of flames or combustible materials.
6. The industrial safe act for the use of open flames in explosion-proof
7. When igniting the Gas Melter keep away from face and body.
8. Make sure that the flame is extinguished before putting away the tool -
9. During operation hot gases emit from the combustion chamber - do not
10. The Gas Melter may only be repaired by the manufacturer. In case
Make use of König's repair service offered at cost price. Simply send in de-
fective device.
env. 10 s • Gaz: Gaz à briquet • Choix des pointes: 2 pièces • Allumoir à pierre
à briquet intégré • Durée de vie de la pierre à briquet: env. 1000 allumages •
Commutateur Marche/Arrêt: commutateur de sécurité • Température réglable
• Garantie 1 an
AVANT LA MISE EN SERVICE :
Lire attentivement la notice d' e mploi et les recommandations de sécurité!
En raison des régulations légales le Fer à Fondre au Gaz est délivré en condi-
tion vide. Ne faire fonctionner l'appareil qu'avec du gaz à briquet de qualité.
expose to heat above +50°C (+120°F) and avoid prolonged exposure to
the sun.
sectors has to be observed.
please always use the safety stand.
leave unattended.
of interference by others the manufacturer refuses any claims on both
guarantee and liability.
art. no. 439 002
art. no. 439 005
art. no. 439 018
art. no. 439 440
Publicité
Table des Matières
