General Safety Warnings - Dremel DigiLab 3D45 Traduction De La Notice Originale

GB
ORIGINAL INSTRUCTIONS

GENERAL SAFETY WARNINGS

WARNING
!
MANUAL AND FAMILIARIZE YOURSELF
WITH THE DREMEL 3D45 BEFORE SETUP
AND USE. FAILURE TO COMPLY WITH THE
WARNINGS AND INSTRUCTIONS MAY RESULT IN
FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE,
OR PERSONAL INJURY. SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE REFERENCE
WORK AREA SAFETY
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate Dremel 3D45 in the presence of
flammable liquids, gases or dust. Dremel 3D45
creates high temperatures which may ignite the
dust or fumes.
c. Store idle 3D45s out of reach of children and
other untrained persons. Injury can occur in
hands of untrained users.
ELECTRICAL SAFETY
a. Always use the Dremel 3D45 with a properly
grounded outlet. Do not modify Dremel 3D45
plug. Improper grounding and modified plugs
increase risk of electric shock.
b. Do not use Dremel 3D45 in damp or wet
locations. Do not expose Dremel 3D45 to rain.
Presence of moisture increases risk of electric
shock.
c. Do not abuse the cord. Never use the cord for
pulling or unplugging the Dremel 3D45.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
d. Avoid using this product during an electric
storm. There may be a remote risk of a power
surge from lightning that may result in an electric
shock.
e. In case of emergency unplug Dremel 3D45 from
outlet.
PERSONAL SAFETY
a. Stay alert, watch what you are doing and
use common sense when operating a Dremel
3D45. Do not use Dremel 3D45 while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating Dremel 3D45 may result in personal
injury.
b. Use personal protective equipment. The use of
protective equipment such as heat resistant gloves
and safety glasses will reduce the risk of personal
injuries.
c. Dress properly. Do not wear loose clothing or
Jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, Jewellery
or long hair can be caught in moving parts.
DREMEL 3D45 USE AND CARE
a. Before every use check Dremel 3D45 for
misalignment or binding of moving parts,
breakage of parts and any other condition
READ ALL
INSTRUCTIONS IN THIS
that may affect the Dremel 3D45's operation.
If damage is suspected then have the Dremel
3D45 repaired by an authorised Dremel service
centre before use. Use of Dremel 3D45 when
damaged may result in poor quality of object
creation, further equipment damage, property
damage or personal injury.
b. Do not touch the extruder tip or heated build
platform during Dremel 3D45 operation or until
it has cooled down to at least 60°C (140°F).
Contact with the extruder tip or heated build
platform during or after operation before tip has
cooled may result in personal injury.
c. Set up the Dremel 3D45 in a well-ventilated
area. Place Dremel 3D45 printer on flat
nonflammable surface and away from
flammable material. Provide at least 8 inches
of unobstructed spacing around Dremel 3D45.
Dremel 3D45 melts plastic during building. Plastic
odours emitted during Dremel 3D45 operation
may irritate eyes and airways. Locating Dremel
3D45 close to surrounding objects prevents proper
ventilation.
d. Do not reach inside the Dremel 3D45 while it is
in operation. Contact with Dremel 3D45 moving
parts during operation may result in poor build
quality, equipment damage or personal injury.
e. Always monitor the Dremel 3D45 during
operation. Use of Dremel 3D45 by persons
unfamiliar with these warnings and instructions may
result equipment or property damage and personal
injury.
f. Use only DREMEL filament. Use of filament not
authorized by Dremel may result in equipment,
property damage or personal injury.
g. Do not adjust extruder/nozzle setting to
exceed the maximum rated temperature of the
filament type being used. Heating filament above
recommended range can cause emissions that may
result in personal injury.
h. Ensure small objects created by Dremel 3D45
are not accessible to young children. Small
objects are potential choking hazards for young
children.
i. Do not create illegal or inappropriate objects
using Dremel 3D45.
j. Do not use Dremel 3D45 to create objects
intended for use with candles, liquid fuels,
and other heat sources. Plastic may melt when
exposed to fire or other heat sources. Such use of
objects created by Dremel 3D45 may result in fire,
property damage and personal injury.
k. Do not use Dremel 3D45 to create objects
intended for food or drink applications
such as preparation, decoration, storage, or
consumption. Such use of objects created by
Dremel 3D45 may result in illness or personal
injury.
l. Do not use Dremel 3D45 to create objects
intended with use with electrical components
or housings of electrical components. Dremel
filament is not suitable for electrical applications.
Such use of objects created by Dremel 3D45 may
result in property damage and personal injury.
m. Do not put plastic objects in or around your
mouth. Dremel filament is not suitable for food
or drink preparation and food utensils. Such use
of objects created by Dremel 3D45 may result in
illness or personal injury.
n. Do not use Dremel 3D45 to create objects
intended for chemical storage. Dremel filament
is not suitable for chemical storage. Such use of
2