THOMSON WHP5407 Mode D'emploi page 8

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 10
• We recommend you adjust the antenna vertically to
ensure optimal reception.
• In many cases, the signal strength varies depending on
the installation location. To improve reception, choose an
installation location near a window.
• Press the INPUT button on the transmitter (10) until you are
in DAB mode (alternatively the INPUT button (24) of the
remote control).
• For a first-time installation, an automatic station search takes
place; alternatively, press the INFO button (6) to start the
automatic station search (Scanning).
• Press and hold TUNE+ (5) or TUNE – (8) to view a list of
available stations.
• Press TUNE + (5) or TUNE – (8) to select a station from the
station list (alternatively the TUNE + or TUNE - button (24)
on the remote control).
• Confirm your selection by pressing the Info button (6) or wait
until the station is automatically adjusted.
• To program the quick-selection buttons M1 to M3, press
and hold one of the favourites buttons (4) on the station you
would like to store as a preset.
• Press the M Set button (7) to view or store your complete
favourites list. For this purpose, first select stations you wish
to store and press the M SET button (7). Use the TUNE +/-
buttons to search for an empty station preset 'Preset Store
(Empty)'. The station is automatically stored in this preset.
• To get additional DAB+ station information, press the INFO
button (6) repeatedly (for example, programme information,
DAB+ frequency, signal information, transmission quality,
time, date, signal strength of the transmitter, etc.).
Note: The signal strength display of the weakest DAB+
station may be helpful in adjusting the rod antenna or
positioning the transmitting station.
8.3 Receiving and playing FM radio
• Press the Input button (10) repeatedly until you are in FM
mode (alternatively the INPUT button (24) of the remote
control).
• Press and hold TUNE + (5) or TUNE- (8) for the automatic
station search to stop at the nearest station with a strong
reception. Alternatively, you can manually set a transmission
frequency by briefly pressing the TUNE + (5) or TUNE - (8)
button. This is also possible using the TUNE+/- buttons (24)
on the remote control.
• To store the desired stations, you can now store the
transmission frequency.
• To program the quick-selection buttons M1 to M3, press
and hold one of the favourites buttons (4) on the station you
would like to store as a preset.
• Press the M Set button (7) to view or store your complete
favourites list. For this purpose, first select stations you wish
to store and press the M SET button (7). Use the TUNE +/-
buttons to search for an empty station preset 'Preset Store
(Empty)'. The station is automatically stored in this preset.
The preset number (for example, P4) is shown in the upper-
left area of the LCD display (9).
6
• To get additional RDS station information, press the INFO
button (6) repeatedly (for example, programme information,
frequency, STEREO/MONO, time, date, etc.).
8.4 General/system settings
• Press and hold the transmitter's POWER button (11) for one
second to switch on the transmitter.
• Press the INPUT button (10) repeatedly until you are in
AUX-IN mode.
• Press and hold the INFO button (6) for about 2–3 seconds
until 'System' appears in the LCD menu.
• Press TUNE + (5) or TUNE - (8) to select your setting. Press
the INFO button (6) to confirm each of your entries. Use the
INPUT button (10) to end your entries/changes.
• The following menu items are available:
Time
(Date and time settings)
Confirm your selection by pressing the Info button (6).
Set the following information in the order listed:
Set Time/Date
Auto Update
Set 12/24 hour
Set date format
Factory Reset
(Resetting to factory settings)
Select the Factory Reset menu item.
Confirm your selection by pressing the INFO button (6).
Press Tune + (5) or Tune – (8) to choose between YES and NO.
Confirm your selection by pressing the INFO button (6).
Software Upgrade
Software update only for authorised dealers
SW Version
(display of the software version)
Select the SW Version menu item.
Confirm your selection by pressing the INFO button (6).
The current software version is displayed.
8.5 Troubleshooting
8.5.1 No sound
• Make sure that the power supply unit is correctly connected
to the wall socket and to the transmitter's power socket.
• Check whether the headphones are on.
• The headphone charge level may be too low, in which case
you need to fully charge the batteries.
• Make sure that the desired TV set or audio device is switched
on and playing sound.
• The headphone volume may be too low.
• The audio signal may be too low. Increase the volume on
your playback device.
• Make sure that the transmitter and receiver (headphones) are
paired > Point 8.1.

Publicité

Table des Matières
loading

Table des Matières