Table Des Matières - Chamberlain LiftMaster CB24 Notice D'utilisation

SPECIFICATIONS
Carton Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Control Board Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
WARNINGS
Safety Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Suggested Entrapment Protection Device Locations . . . . . . . . . .4
WIRING
Control Box Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Earth Ground Rod Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Wiring Of Motor To Control Board . . . . . . . . . . . . . . . . . . . . . . . .9
BASIC CONTROL BOARD SETUP
Set Dip Switch for Gate Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Install Radio Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Programming Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Wire Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Optional Control Devices . . . . . . . . . . . . . . . . . . . . . . . . . . .11-13
Force and Timer to Close . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Program Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
OPERATION and MAINTENANCE
First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
WIRING DIAGRAM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLESHOOTING
. . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
REPAIR PARTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
SAFETY PRECAUTIONS FOR SWING and ORNAMENTAL "GRILL TYPE GATES"
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect
anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open
and close gate cycles.
• Locate entrapment protection devices to protect between moving
gate and RIGID objects, such as posts.
• A swinging gate shall NOT open into public access ways
T A B L E O F C O N T E N T S
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of serious
injury or death if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your gate and/or the gate
operator if you do not comply with the cautionary statements that
accompany it. Read them carefully.
IMPORTANT NOTE
• BEFORE attempting to install, operate or maintain the operator,
you must read and fully understand this manual and follow all
safety instructions.
• These instructions are intended to highlight certain safety
related issues. These instructions are not intended to be
comprehensive. Because each application is unique, it is the
responsibility of the purchaser, designer, installer and end user
to ensure that the total gate system is safe for its intended use.
• Save These Instructions
I N S T A L L A T I O N
We recommend to use E-locks/Maglock against vandilism and if gate
is installed where strong winds may appear.
2
Mechanical
Electrical
01-G0665F18