Parts List; Accessories - Binks AA4400M Instructions De Service

When ordering, please specify Part No. (Not all Part Nos. are available for purchasing.)
ITEM PART
NO. NO. DESCRIPTION
1 — GUN BODY ..................................... 1
2 SPA-71-K5 BAFFLE PLATE (KIT OF 5) ..................... 1
FLAT TIP COMPONENTS
3 54-5799-K ✙ FLUID SEAT (4400PSI) ......................... 1
(TUNGSTEN CARBIDE) ..................................
4 SPA-98-K5 GASKET (KIT OF 5) ............................ 1
5 114-XXXXX ■ FLAT TIP (FINE FINISH TIPS 9-XXXX-F) ....... 1
6 54-5878-K ▼ FLAT TIP HVLP AIRCAP ....................... 1
(FLAT TIP TRANS-TECH AIRCAP 54-5797-K)
(AA-10 FLAT TIP HVLP AIRCAP 54-5890-K)
7 54-5852 RETAINING RING .............................. 1
8 54-5794 m FLAT TIP GUARD .............................. 1
TWIST TIP COMPONENTS
3A 54-5832-K ✙ TWIST TIP FLUID SEAT (4400PSI) ............ 1
(TUNGSTEN CARBIDE)
5A 9-XXX-75 ■ TWIST TIP ...................................... 1
5B 54-7539-K2 TWIST TIP BRACE (KIT OF 2) ................. 1
6A 54-5924-K ▼ TWIST TIP HVLP AIRCAP ..................... 1
(TWIST TIP TRANS-TECH AIRCAP 54-5925-K)
7 54-5852 RETAINING RING .............................. 1
8A 54-5921 m TWIST TIP GUARD ............................. 1
▼ All aircap kits are pre-assembled with Retaining ring and
appropriate tip guard. When switching from flat tip to
twist tip, or vice versa, be sure to order correct fluid seat
(3/3A). For twist tip, item 5B will also be needed.
■ Refer to page 10 for available tip sizes. When purchasing
twist tip, discard packaged brace/seal and use Item 5B
only.
✙ Pre-assembled with gasket SPA-98.
▲ Available as part of kit 54-5835.
➣ Available as part of kit 54-5838. Order Filter (12) separately.
71-4993 25' 1/8" High Pressure Fluid Hose Assembly
71-4995 25' 3/16" Low Pressure (1900PSI Max) Fluid Hose
Assembly
FITTINGS
54-4976-K3 3-Pack 1/4" NPT(f) x 3/8" O.D. Push-In Tube Fitting
(optional)
72-2332 Fluid Inlet Swivel (1/4"m x 1/4"f)
FLUID FILTER
54-5788-K5 60 Mesh (Screen) Gun Mounted Filter
54-5789-K5 100 Mesh (Screen) Gun Mounted
Filter 54-1835 100 Mesh (Edge) Filter
54-1836 60 Mesh (Edge) Filter
AA4400M AIR-ASSIST AIRLESS SPRAY GUN

PARTS LIST

Refer to page 12 when referencing Item Nos.
QTY.

ACCESSORIES

14 / 12
ITEM PART
NO. NO. DESCRIPTION
9 SN-402-K AIR VALVE ASSEMBLY ......................... 1
10 — ▲ TRIGGER ....................................... 1
11 54-5780 FLUID TUBE ASSEMBLY ....................... 1
12 54-5789-K5 o FLUID FILTER 100 MESH (KIT OF 5) .......... 1
(60 MESH FILTER (KIT OF 5) 54-5788-K5)
13 — ➣ FLUID INLET SWIVEL (1/4" NPS) ............ 1
14 — ➣ FILTER ADAPTER NUT ........................ 1
15 SN-9-K3 AIR INLET FITTING 1/4" NPS (KIT OF 3) ..... 1
16 — ● FILTER BRACKET SCREW ..................... 1
17 — ● FILTER BRACKET .............................. 1
18 54-5826 FLUID NEEDLE ASSEMBLY KIT (4400PSI) .... 1
19 54-5850 BLANKING NEEDLE NUT ...................... 1
22 54-5815 SPREADER VALVE ASSEMBLY ................. 1
23 — # BODY BUSHING .............................. 1
24 — # BODY BUSHING GASKET .................... 1
25 — ▲ TRIGGER NUT ................................. 1
26 — ▲ TRIGGER SCREW .............................. 1
27 — 6 TOP FILTER SEAL ............................. 1
28 — 6 BOTTOM FILTER SEAL ....................... 1
29 54-1835 100 MESH DISC FILTER (1 PIECE) ............ 1
(60 MESH FILTER (KIT OF 5) 54-1836-K5)
30 — * DISC FILTER HOUSING .................... 1
31 — * DISC FILTER RETAINING NUT ............... 1
● Available as part of kit 54-5827.
# Available as part of kit 54-5829.
m Mandatory for operating pressures above 1000 psi.
o Assembled with filter seals.
6 Available in 10 pack as part of kit 54-5874-K10
(note assembly location on next page).
* Available as part of kit 54-4726-K. Order filter (29)
separately.
EN
QTY.